Cisco Cisco TelePresence Video Communication Server Expressway 관리 매뉴얼
About Downspeeding
If bandwidth control is in use, there may be situations when there is insufficient bandwidth available to place a call at
the requested rate. By default (and assuming that there is some bandwidth still available) the VCS will still attempt to
connect the call, but at a reduced bandwidth – this is known as downspeeding.
the requested rate. By default (and assuming that there is some bandwidth still available) the VCS will still attempt to
connect the call, but at a reduced bandwidth – this is known as downspeeding.
Downspeeding can be configured so that it is applied in either or both of the following scenarios:
■
when the requested bandwidth for the call exceeds the lowest per-call limit for the subzone or pipes
■
when placing the call at the requested bandwidth would mean that the total bandwidth limits for that subzone
or pipes would be exceeded
or pipes would be exceeded
You can turn off downspeeding, in which case if there is insufficient bandwidth to place the call at the originally
requested rate, the call will not be placed at all. This could be used if, when your network is nearing capacity, you
would rather a call failed to connect at all than be connected at a lower than requested speed. In this situation
endpoint users will get one of the following messages, depending on the system that initiated the search:
requested rate, the call will not be placed at all. This could be used if, when your network is nearing capacity, you
would rather a call failed to connect at all than be connected at a lower than requested speed. In this situation
endpoint users will get one of the following messages, depending on the system that initiated the search:
■
"Exceeds Call Capacity"
■
"Gatekeeper Resources Unavailable"
About Subzones
The Local Zone is made up of subzones. Subzones are used to control the bandwidth used by various parts of your
network, and to control the VCS's registration, authentication and media encryption policies.
network, and to control the VCS's registration, authentication and media encryption policies.
based on endpoint IP address ranges or alias pattern matches.
page (Configuration > Local Zone > Subzones).
Three special subzones — the Default Subzone, the Traversal Subzone and the Cluster Subzone (only applies if the
VCS is in a cluster) — are automatically created and cannot be deleted.
VCS is in a cluster) — are automatically created and cannot be deleted.
Default links between subzones
The VCS is shipped with the Default Subzone and Traversal Subzone (and Default Zone) already created, and with
links between them. If the VCS is added to a cluster then default links to the Cluster Subzone are also established
automatically. You can delete or amend these
links between them. If the VCS is added to a cluster then default links to the Cluster Subzone are also established
automatically. You can delete or amend these
if you need to model restrictions of your network.
About the Traversal Subzone
The Traversal Subzone is a conceptual subzone. No endpoints can be registered to the Traversal Subzone; its sole
purpose is to control the bandwidth used by
purpose is to control the bandwidth used by
The Traversal Subzone page (Configuration > Local Zone > Traversal Subzone) allows you to place bandwidth
restrictions on calls being handled by the Traversal Subzone and to configure the range of ports used for the media in
traversal calls.
restrictions on calls being handled by the Traversal Subzone and to configure the range of ports used for the media in
traversal calls.
Configuring Bandwidth Limitations
All traversal calls pass through the Traversal Subzone, so by applying bandwidth limitations to the Traversal Subzone
you can control how much processing of media the VCS will perform at any one time. These limitations can be
applied on a total concurrent usage basis, and on a per-call basis.
you can control how much processing of media the VCS will perform at any one time. These limitations can be
applied on a total concurrent usage basis, and on a per-call basis.
Configuring the Traversal Subzone Ports
On Configuration > Local Zone > Traversal Subzone you can configure the range of ports used for media in traversal
calls.
calls.
226
Cisco TelePresence Video Communication Server Administrator Guide