PEHA Aura D 20.450.21 FU-BLS 사용자 설명서

4-channel switching module, for mounting on DIN rail, with two pushbuttons, 

454 FU-E REG

380213

each with ON/OFF function. 
30 Easyclick transmitters can be trained to work with one receiver. 
Connection options: 2 push-to-make switches and 2 changeover contact (zero-potential 
and independently programmable), dimensions: 72 mm wide (4 module widths),
Aerial 460 ANT is needed. 
Supply voltage 230 V, 50 Hz, neutral conductor required, screw terminals, 
the contacts must not be operated with mixed voltages (i.e. safety extra-low voltage 
and 230 V). 
Connection data for electrically powered units 
per channel: 

push-to-make (PTM)  push-to-break (PTB)

Filament lamp (ohmic load)

2500 W

1000 W

High-voltage halogen lamps

1250 W

500 W

Inductive load

600 VA

250 W

Electronic ballast

3 pieces 

1 piece

External aerial with magnetic base. Improves the reception of 

460 ANT

378213

Easyclick flush-mounted series receivers and the Easyclick interface.

The Easyclick PHC/PHC-Compact interface permits connection between the

940 FU C 

262217

Easyclick radio transmitters and the PHC or PHC-Compact system,
this includes connection cable 30 cm, 72 mm wide (4 module widths). 
The Easyclick PHC/PHC-Compact interface has 32 inputs for Easyclick transmitters and 
it converts the radio signals from these into input signals for the PHC or PHC-Compact 
system. The electrically powered units are driven via output, shutter, and dimmer 
modules. Up to a total of 240 transmitters for ON/OFF can be trained. 
The Easyclick PHC/PHC-Compact interface 940 FU C must be programmed using the 
PHC software, version 2.4 and above. 
Technical data:
Power supply:

24V DC via the PHC bus

Internal consumption:

approx. 30 to 40 mA

Operating controls:

2 pushbuttons “Program” and “Clear”

Display elements:

1 LED for receive 
3 x 7 segment display for channel setting

Transmission frequency: 868,3 MHz
Connections:

2 modular sockets for the PHC bus 
1 aerial socket for an external aerial 
(Antenna 460 ANT is needed)

The Easyclick-PHC interface permits bidirectional connection between the Easyclick radio 

941 FU C

262717

transmitters and receivers and the PHC system, this includes connecting cable 30 cm, 
72 mm wide (4 module widths). 
The Easyclick PHC interface has 120 inputs for Easyclick transmitters; it converts the radio 
signals from these into input signals for the PHC system. Up to a total of 240 individual 
transmitter channels (pushbuttons etc.) distributed over any number of inputs can be trained. 
The Easyclick PHC interface also has 120 outputs for Easyclick switching receivers, 
shutters/blinds receivers, and dimmer receivers. The Easyclick PHC interface 941 FU-C 
must be programmed using the PHC software, version 2.8 and above (German version)
Technical data:
Power supply:

24 V DC via the PHC bus

Internal consumption:

30 to 40 mA

Operating controls:

2 pushbuttons “Program” and “Send/Clear”

Display elements:

2 LEDs, send (red) and receive (green)
3 x 7 segment display for channel setting

Transmission frequency: 868,3 MHz
Terminals:

2 modular sockets for the PHC bus
1 aerial socket for an external aerial 
(460 ANT is needed)

for checking the strength of Easyclick radio signals and for determining 

450 TEST

386513

the best positions for transmitters and receivers .
Dimensions: 150 x 50 x 22 mm (L x W x H),
battery: 9-volt block (not included in delivery).

Article designation

Colour

Article No.

Code No.