Cisco Cisco TelePresence MX700 설치 가이드
Configuring IP
(When not set by a provisioning system)
On the Touch controller, you can select the IP settings for the
upcoming calls. If you wish to change the IP settings from the
default dual stack setting to either IPv4 or IPv6, you can do that
on the web interface.
The system’s IP configuration is by default set to dual stack.
This means that the network interface can operate on both IP
versions, and has both an IPv4 and an IPv6 address at the same
time. The IP parameters can be assigned automatically by the
network, or you can set everything manually.
If you want to set the parameters manually, please contact
your network administrator to obtain the required parameters.
If your system is provisioned automatically, these IP settings
may be overridden by the provisioning system.
To go back to default IP settings tap the user name in the upper
left corner and
tap
Settings > Administrator > IP & VLAN
and
Default
.
If an IPv4 or IPv6 address is already assigned to the system, you
will find it in the NETWORK section on the System Information
page: Tap the user name in the upper left corner and
tap
Settings > System Information.
To set or change the IPv4 settings
1.
Choose IP version
Tap the user name in the upper left corner and tap
Settings
> Administrator > IP & VLAN
. Then tap
Advanced Settings
.
Check the
IPv4
box, if it has not been checked.
2.
Choose automatic or manual IP assignment
Tap the arrow ( ∨
) beside IPv4. Tap
DHCP
in the
IP
Assignment
section if you want automatic IP assignment;
or
Static
if you want to set the IP addresses manually.
3.
If IP Assignment is Static: Set the IP addresses
Enter the
IP Address
,
Subnet Mask
,
Gateway
, and
DNS
Server
address. A soft keyboard appears when you tap
an input field.
4.
Save the settings
Tap
Save
to confirm the changes, or
Undo
to leave without
saving.
5.
Return to the main menu
Tap
Exit
to return to the home menu.
* IP Assignment:
DHCPv6: All IPv6 addresses, including options like the DNS and NTP
server addresses, are obtained automatically from a DHCPv6 server.
Autoconf: The system and gateway IP addresses will be assigned
automatically. The options, e.g. NTP and DNS server addresses, must be
set/assigned according to the DHCP Options setting. **
Static: The system and gateway IP addresses must be configured manually.
The options, e.g. NTP and DNS server addresses, must be set/assigned
according to the DHCP Options setting. **
To set or change the IPv6 settings
1.
Choose IP version
Tap the user name in the upper left corner and
tap
Settings
> Administrator > IP & VLAN
. Then tap
Advanced Settings
.
Check the
IPv6
box, if it has not been checked.
2.
Choose automatic or manual IP assignment
Tap the arrow ( ∨
) beside IPv6. Choose
DHCPv6
,
Autoconf
or
Static
in the
IP Assignment
section according to your
network requirements.*
3.
If IP Assignment is Static: Set the IP addresses
Enter the
IP Address
and
Gateway
. A soft keyboard appears
when you tap an input field.
4.
If IP Assignment is Static or Autoconf: Set DHCPOptions
Tap
On
or
Off
in the
DHCP Options
section according to
your network requirements.**
If DHCP Options are switched Off, you must set the DNS
and NTP server addresses on the web interface.
5.
Save the settings
Tap
Save
to confirm the changes, or
Undo
to leave without
saving.
6.
Return to the main menu
Tap
Exit
to return to the home menu.
** DHCP Options:
On: The IP parameters, like the DNS and NTP server addresses, will be
obtained automatically from a DHCPv6 server.
Off: The IP parameters, like the DNS and NTP server addresses, must be
set manually.
Back to task overview
Cisco TelePresence Video Systems
D14639.15 Video Systems Getting Started Guide TC7.2, OCTOBER 2014.
Copyright © 2010–2014 Cisco Systems, Inc. All rights reserved.
14
Getting Started Guide
Contents
Introduction
User interfaces
Configuration
Appendices
Contacts
Configuration