Cisco Cisco IOS Software Release 15.2(3)E 릴리즈 노트
30
Release Notes for the Catalyst 4500 Series Switch, Cisco IOS Releases 15.2(2)Ex
Upgrading the System Software
To upgrade the Cisco IOS software on your Catalyst 4500 series switch, use this procedure:
Step 1
Download Cisco IOS Release 15.1(2)SG from Cisco.com, and place the image on a TFTP server in a
directory that is accessible from the supervisor engine that is upgraded.
directory that is accessible from the supervisor engine that is upgraded.
Step 2
Use the dir bootflash: command to ensure that there is sufficient space in Flash memory to store the
promupgrade image. If there is insufficient space, delete one or more images, and then enter the
squeeze bootflash: command to reclaim the space.
promupgrade image. If there is insufficient space, delete one or more images, and then enter the
squeeze bootflash: command to reclaim the space.
If you are using a CompactFlash card, use slot0: instead of bootflash.
Step 3
Download the software image into Flash memory using the copy tftp command.
The following example shows how to download the Cisco IOS software image
cat4000-is-mz.121-12c.EW from the remote host 172.20.58.78 to bootflash:
cat4000-is-mz.121-12c.EW from the remote host 172.20.58.78 to bootflash:
Switch# copy tftp: bootflash:
Address or name of remote host [172.20.58.78]?
Source filename [cat4000-is-mz121_12c.EW]?
Destination filename [cat4000-is-mz.121-12c.EW]?
Accessing tftp://172.20.58.78/cat4000-is-mz.121-12c.EW...
Loading cat4000-is-mz.121-12c.EW from 172.20.58.78 (via
FastEthernet2/1):!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
|!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
[OK - 6923388/13846528 bytes]
6923388 bytes copied in 72.200 secs (96158 bytes/sec)
Switch#
Step 4
Use the no boot system flash bootflash:file_name command to clear the cat4000-is-mz.121-8a.EW file
and to save the BOOT variable.
and to save the BOOT variable.
The following example shows how to clear the BOOT variable:
Switch# configure terminal
Switch(config)# no boot system flash bootflash:cat4000-is-mz.121-8a.EW
Switch(config)# exit
Switch# write
Building configuration...
Compressed configuration from 3641 to 1244 bytes [OK]
Switch#
Step 5
Use the boot system flash command to add the Cisco IOS software image to the BOOT variable.
The following example shows how to add the cat4000-is-mz.121-12c.EW image to the BOOT variable:
Switch# configure terminal
Switch(config)# boot system flash bootflash:cat4000-is-mz.121-12c.EW
Switch(config)# exit
Switch# write