Cisco Cisco IOS Software Release 12.4(23) 릴리즈 노트
596
Caveats for Cisco IOS Release 12.4
OL-7656-15 Rev. J0
Resolved Caveats—Cisco IOS Release 12.4(7d)
Conditions: These symptoms are observed on a Cisco platform when the FIN flag is set in the initial
ESTAB message from a neighbor. You must reload the router to recover from the symptoms.
ESTAB message from a neighbor. You must reload the router to recover from the symptoms.
Workaround: Do not enter the copy ftp disk command. Rather, enter the copy tftp disk command.
•
CSCse05736
Symptoms: A router that is running RCP can be reloaded by a specific packet.
Conditions: This symptom is seen under the following conditions: 1. The router must have RCP
enabled. 2. The packet must come from the source address of the designated system configured to
send RCP packets to the router. 3. The packet must have a specific data content.
enabled. 2. The packet must come from the source address of the designated system configured to
send RCP packets to the router. 3. The packet must have a specific data content.
Workaround: Put access lists on the edge of your network blocking RCP packets to prevent spoofed
RSH packets. Use another protocol such as SCP. Use VTY ACLs.
RSH packets. Use another protocol such as SCP. Use VTY ACLs.
Wide-Area Networking
•
CSCek55209
Symptoms: When the ppp multilink endpoint mac lan-interface command or the ppp multilink
endpoint ip ip-address command is configured, the router may unexpectedly reload if the multilink
interface goes to the DOWN state, for example, when a PVC virtual circuit is unconfigured.
endpoint ip ip-address command is configured, the router may unexpectedly reload if the multilink
interface goes to the DOWN state, for example, when a PVC virtual circuit is unconfigured.
Conditions: This symptom is observed on a Cisco router that is configured for Multilink PPP.
Workaround: There is no workaround. Do not use these configuration commands in Cisco IOS
Releases 12.3, 12.4 or 12.2SB without a fix for this DDTS.
Releases 12.3, 12.4 or 12.2SB without a fix for this DDTS.
•
CSCek56250
Symptoms: A router may reload while executing the show ppp multilink command.
Conditions: This symptom is observed when a multilink bundle goes down while the output is being
generated.
generated.
Workaround: There is no workaround.
•
CSCek59078
Symptoms: An L2TPv3 session is established when voluntary tunneling is configured and both peers
have corresponding configurations. However, after configuring the pseudowire on UUT virtual-PPP
interface, sessions on UUT and peer are UP, but “virtual-PPP1 is up, line protocol is down.”
have corresponding configurations. However, after configuring the pseudowire on UUT virtual-PPP
interface, sessions on UUT and peer are UP, but “virtual-PPP1 is up, line protocol is down.”
Conditions: For this symptom to occur, the virtual-ppp interface was previously deleted using the
no interface virtual-ppp n command, and then reinstated using the interface virtual-ppp n
command.
no interface virtual-ppp n command, and then reinstated using the interface virtual-ppp n
command.
Workaround: Be certain that the virtual-PPP interface has never been unconfigured using the no
interface virtual- ppp n configuration command since the router was booted.
interface virtual- ppp n configuration command since the router was booted.
•
CSCir00712
Symptoms: When a LAC receives fragmented data traffic over an L2TP tunnel, the IP layer
reassembles the packets and routes them over the wrong interface instead of processing them locally.
reassembles the packets and routes them over the wrong interface instead of processing them locally.
Conditions: This symptom is observed on a Cisco router that runs Cisco IOS Release 12.3(14)T
when fragmented L2TP data traffic is received on the LAC from the LNS over the L2TP tunnel. The
symptom is release-independent.
when fragmented L2TP data traffic is received on the LAC from the LNS over the L2TP tunnel. The
symptom is release-independent.
Workaround: There is no workaround.
•
CSCsb24255
Symptoms: A router may generate the following error message and a MALLOC failure may occur: