Cisco Cisco Aironet 1530i Outdoor Access Point 릴리즈 노트
7
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 15.2(4)JB5
OL-30935-01
Important Notes
Cisco 1040/1140 series Access Points May Record "watchdog timer expired" as
Last Reset Reason
Last Reset Reason
This error message sometimes appears as the last reset reason when the access points are power cycled:
Watchdog timer expired
This symptom is observed only in the Cisco 1040/1140 series access point and does not have any impact
on functionality. Ignore the “watchdog timer expired” reason after an access point has been power
cycled. You can also overwrite the reset reason to “reload” by rebooting with command operation.
on functionality. Ignore the “watchdog timer expired” reason after an access point has been power
cycled. You can also overwrite the reset reason to “reload” by rebooting with command operation.
Regulatory Update for Japan
This release supports the U regulatory domain for the W52 frequency set (channels 36, 40, 44, and 48)
in Japan for the Cisco Aironet 1230 series. This support was added for the Cisco Aironet 1130 series in
Cisco IOS Software Release 12.4(3G)JA, which shipped previously. Cisco access points specified for
this new domain ship with a U domain radio. Installed J domain access points are automatically upgraded
to the U domain status with this release.
in Japan for the Cisco Aironet 1230 series. This support was added for the Cisco Aironet 1130 series in
Cisco IOS Software Release 12.4(3G)JA, which shipped previously. Cisco access points specified for
this new domain ship with a U domain radio. Installed J domain access points are automatically upgraded
to the U domain status with this release.
For the latest Cisco WLAN compliance status, visit this URL:
.
Point-to-Point and Point-to-Multipoint Bridging Support for 802.11n Platforms
The point-to-point and point-to-multipoint bridging is supported on the Cisco Aironet 1040, 1140, 1260,
1600, 2600, 3500 and 3600 series access points (802.11n platforms). The 5-GHz bands support 20 and
40-MHz channel widths, and the 2.4-GHz bands support only a 20-MHz channel width.
1600, 2600, 3500 and 3600 series access points (802.11n platforms). The 5-GHz bands support 20 and
40-MHz channel widths, and the 2.4-GHz bands support only a 20-MHz channel width.
The following items are supported for AP1040, AP1140, AP1260, AP1600, AP2600, AP3500, and
AP3600 bridging:
AP3600 bridging:
•
MIMO, short-range bridging (on campus or inter-building bridge deployments), with dipole and
MIMO antennas (line of sight and short range) under 1 km.
MIMO antennas (line of sight and short range) under 1 km.
•
20-MHz and 40-MHz 802.11n support.
•
Workgroup bridge (WGB) short-range support.
•
SISO (single-in, single-out), MCS 0-7 and legacy bridge rates (802.11 a/b/g and 802.11n) using one
outdoor antenna.
outdoor antenna.
Note
This is only supported using short range links and is not a replacement for the AP-1300/1400 or other
bridge products.
bridge products.
The following items are not supported for AP 702i, AP1040, AP1140, AP1260, AP1600, AP2600,
AP3500 and AP3600 bridging:
AP3500 and AP3600 bridging:
•
The distance CLI command: long-range links over 1 km currently are not supported; therefore, the
distance command is not supported.
distance command is not supported.