Cisco Cisco Aironet 1310 Access Point Bridge 릴리즈 노트
14
Release Notes for Cisco Aironet 1310 Outdoor Access Point/Bridge for Cisco IOS Release 12.3(2)JA
OL-6723-01
Caveats
•
CSCee90230—When the access point is configured for TACACS+ administrator authentication, this
traceback occurs sometimes when the access point reboots:
traceback occurs sometimes when the access point reboots:
Traceback= 2C120 2C150 2EFC4 2BE34 2BD50 330724 3EBD44 19C888 19E5B0 2A3FC0 3AAA04
1337F8
This occurs if the access point has a DHCP IP address. It does not occur when the access point has
a static IP address.
a static IP address.
•
CSCef11167—When polling cDot11ActiveWireless Clients via SNMP, the response may have a
value of 4294967292. This occurs in the CiscoWorks Wireless Solution Engine (WLSE) as AP in
Overloaded state.
value of 4294967292. This occurs in the CiscoWorks Wireless Solution Engine (WLSE) as AP in
Overloaded state.
There is no workaround for this caveat.
•
CSCef67806—When you enter the show cdp traffic command on a repeater access point or the
parent to which the repeater is associated, the access point reports an inaccurate total of CDP
packets.
parent to which the repeater is associated, the access point reports an inaccurate total of CDP
packets.
•
CSCef65076—The access point GUI sometimes reports this error when you add a RADIUS server
hostname to the access point:
hostname to the access point:
HTTP 400 - Bad Request
Workaround: Enter the server IP address instead of the hostname.
•
CSCef71825—When a memory allocation failure occurs on the access point, it sometimes fails to
respond to authentication requests from client devices running Microsoft Windows CE. The access
point again responds to client requests after you reboot it.
respond to authentication requests from client devices running Microsoft Windows CE. The access
point again responds to client requests after you reboot it.
•
CSCef45010—1310 access point/bridge GUI performs poorly when half duplex and a specified
speed are part of its configuration.
speed are part of its configuration.
If you hardcode the duplex and speed into a configuration for the fast Ethernet interface, the GUI
becomes extremely slow. You may also experience a high number of input errors when you try to
use the GUI. Telnet or console traffic is not affected.
becomes extremely slow. You may also experience a high number of input errors when you try to
use the GUI. Telnet or console traffic is not affected.
Workaround: Set the 1310 Ethernet port settings to Auto Speed and Auto Negotiation.
•
CSCef75032—When you disable the 802.11g radio on the access point GUI, the radio is disabled
but the Settings page and the Network Interfaces page sometimes indicate that the radio is still
enabled.
but the Settings page and the Network Interfaces page sometimes indicate that the radio is still
enabled.
•
CSCef66724—Access point/bridge loses packets due to encryption errors with WPAv2/PSK and
concatenation enabled.
concatenation enabled.
When a 1310 device is configured for WPAv2/PSK and concatenation is enabled, the statistics page
shows all Rx packets to have WEP errors even though no packet concatenations are occurring due
to low traffic volume. No WEP, MIC, or replay errors occur if concatenation is disabled.
shows all Rx packets to have WEP errors even though no packet concatenations are occurring due
to low traffic volume. No WEP, MIC, or replay errors occur if concatenation is disabled.
•
CSCef87205—There are problems with the following SNMP MIB object identifiers in the
CISCO-DOT11-SSID-SECURITY-MIB:
CISCO-DOT11-SSID-SECURITY-MIB:
–
cdot11SecAuxSsidVlanName is not writable unless the value corresponds to the same VLAN
as the cdot11SecAuxSsidVlan already set for the SSID. The same cdot11SecAuxSsidVlanName
and cdot11SecAuxSsidVlan must correspond to an existing entry in the
cdot11SecVlanNameTable.
as the cdot11SecAuxSsidVlan already set for the SSID. The same cdot11SecAuxSsidVlanName
and cdot11SecAuxSsidVlan must correspond to an existing entry in the
cdot11SecVlanNameTable.
–
cdot11SecSsidInformationElement value cannot be modified after it has been set.
–
cdot11SecSsidRedirectFilter allows you to set an ACL number that is outside the valid range.
–
cdot11SecAuxSsidWirelessNetId allows you to set a value only from 0 to 4095.