Cisco Cisco Aironet 1310 Access Point Bridge 릴리즈 노트
16
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 12.4(10b)JA
OL-14517-01
Caveats
•
CSCse34644—Shared authentication with non-native vlan is not working.
Workaround—Save the configuration, and reload the access point. When the access point comes up,
both clients authenticate. Edit the authentication SSID as follows:
both clients authenticate. Edit the authentication SSID as follows:
Add open authentication; remove shared authentication. Then remove open and add shared
authentication, and the client will associate. Save the configuration, and reload the access point.
authentication, and the client will associate. Save the configuration, and reload the access point.
•
CSCse48137—Nested repeater does not work.
A nested 1130 access point configured for open authentication and root mode station role fails to
associate with a repeater and displays this console message:
associate with a repeater and displays this console message:
*Mar 1 00:01:34.822:%DOT11-4-CANT_ASSOC: Interface Dot11Radio1, cannot associate: No
Response
*Mar 1 00:02:17.603:%DOT11-6-DFS_SCAN_COMPLETE: DFS scan complete on frequency 5560
MHz
*Mar 1 00:02:31.821:%DOT11-4-CANT_ASSOC: Interface Dot11Radio1, cannot associate: Rcvd
response from 0014.6956.5cda channel 149 801
•
CSCsf06407—Packets from Cisco 7920 phones always fall into the COS 6 queue. This problem
occurs when the stream feature is enabled.
occurs when the stream feature is enabled.
Workaround: None.
•
CSCsf14351—Medium time restriction affects built-in bridge functionality on Theseus.
•
CSCsf27222—Unable to maintain more than 7 voice calls.
Workaround: None.
•
CSCsg74791—Time-based ACLs do not work properly on Cisco Aironet IOS access points.
The access point does not recognize the specified time-range. Either the ACL becomes active as
specified, and the access point does not recognize when the ACL becomes inactive, thus continuing
to apply the ACL; or the ACL is applied immediately when it is enabled on an interface (radio or
fa0).
specified, and the access point does not recognize when the ACL becomes inactive, thus continuing
to apply the ACL; or the ACL is applied immediately when it is enabled on an interface (radio or
fa0).
•
CSCsg80305—When 16 SSIDs are configured, client devices sometimes fail to associate to the 16th
SSID.
SSID.
Workaround: Save the configuration and reload the UC520.
•
CSCsg88872—Client devices can sometimes associate to an access point when WEP is set to
optional on the client but set to required on the access point.
optional on the client but set to required on the access point.
Workaround: None.
•
CSCsg90606—When an SSID is configured with WPA version 2+CCKM and encryption is set to
TKIP, wireless clients fail to authenticate to the access point.
TKIP, wireless clients fail to authenticate to the access point.
Workaround: None.
•
CSCsh44876—The access point incorrectly lists client wired interface IP addresses in show dot11
assoc command output and in the association table.
assoc command output and in the association table.
Workaround: None.
•
CSCsh84949—Wireless client fails to receive multicast data stream.
Workaround—Configure no ip igmp snooping on the access point.
•
CSCsh86675—1310 Bridge continuously authenticates and deauthenticates with LEAP enabled.
Occurs when 1310 configured as an access point and associating with an Intel 2915 802.11g radio.
Client running LEAP associates and disassociates with the client disauthenticating.
Client running LEAP associates and disassociates with the client disauthenticating.