Cisco Cisco Aironet 350 Access Points 릴리즈 노트
2
Release Notes for Cisco Aironet 350, 1100, and 1200 Series Access Points for Cisco IOS Release 12.2(13)JA
OL-4529-01
Introduction
Introduction
The Cisco Aironet Access Point is a wireless LAN transceiver that acts as the connection point between
wireless and wired networks or as the center point of a standalone wireless network. In large
installations, the roaming functionality provided by multiple access points enables wireless users to
move freely throughout the facility while maintaining uninterrupted access to the network.
wireless and wired networks or as the center point of a standalone wireless network. In large
installations, the roaming functionality provided by multiple access points enables wireless users to
move freely throughout the facility while maintaining uninterrupted access to the network.
You can configure and monitor 350, 1100, and 1200 series access points using the command-line
interface (CLI), the browser-based management system, or Simple Network Management Protocol
(SNMP).
interface (CLI), the browser-based management system, or Simple Network Management Protocol
(SNMP).
System Requirements
You can install Cisco IOS Release 12.2(13)JA on all 1100 series access points and on model AP1230
access points. You can also convert 350 and 1200 series access points that run VxWorks to run IOS
software. Your 350 series access point must run one of these VxWorks versions before you can convert
to IOS software: 12.03T, 12.02T1, 12.01T1, 11.23T, or 11.21. Your 1200 series access point must run
one of these VxWorks versions before you can convert to IOS software: 12.03T, 12.02T1, 12.01T1,
12.00T, 11.56, or 11.54T. If your access point runs version 12.04, you must downgrade to a supported
VxWorks version before upgrading to IOS software.
access points. You can also convert 350 and 1200 series access points that run VxWorks to run IOS
software. Your 350 series access point must run one of these VxWorks versions before you can convert
to IOS software: 12.03T, 12.02T1, 12.01T1, 11.23T, or 11.21. Your 1200 series access point must run
one of these VxWorks versions before you can convert to IOS software: 12.03T, 12.02T1, 12.01T1,
12.00T, 11.56, or 11.54T. If your access point runs version 12.04, you must downgrade to a supported
VxWorks version before upgrading to IOS software.
To install this release on a 350 or 1200 series access points that do not run IOS software, use the
conversion utility to convert to IOS software without losing your current configuration. To convert to
IOS software without saving your configuration, load the conversion upgrade image. The access point
reboots with IOS software and factory default settings.
conversion utility to convert to IOS software without losing your current configuration. To convert to
IOS software without saving your configuration, load the conversion upgrade image. The access point
reboots with IOS software and factory default settings.
Note
Cisco Aironet 340 Series Access Points do not support IOS software. Do not attempt to load an IOS
image on 340 series access points or on 350 and 1200 series access points that have not been converted
to IOS software.
image on 340 series access points or on 350 and 1200 series access points that have not been converted
to IOS software.
Finding the IOS Software Version
To find the version of IOS software running on your access point, use a Telnet session to log into the
access point and enter the show version EXEC command. This example shows command output from
an access point running Cisco IOS Release 12.2(11)JA:
access point and enter the show version EXEC command. This example shows command output from
an access point running Cisco IOS Release 12.2(11)JA:
ap1200>show version
Cisco Internetwork Operating System Software
IOS (tm) C1200 Software (C1200-K9W7-M), Version 12.2(11)JA
Copyright (c) 1986-2003 by Cisco Systems, Inc.
On access points running IOS software, you can also find the software version on the System Software
Version page in the access point’s web-browser interface.
Version page in the access point’s web-browser interface.
If your access point does not run IOS software, the software version appears at the top left of most pages
in the web-browser interface.
in the web-browser interface.