Cisco Cisco Aironet 1400 Wireless Bridge 릴리즈 노트
20
Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 12.4(10b)JDA and 12.4(10b)JDA2
OL-17693-02
Caveats
Caveats
This section lists open and resolved caveats for access points and bridges in Cisco IOS Releases
12.4(10B)JDA. and 12.4(10b)JDA2
12.4(10B)JDA. and 12.4(10b)JDA2
Open Caveats
These caveats are open in Cisco IOS Release 12.4(10B)JDA and 12.4(10b)JDA2.
•
CSCsv36602—Files appearing on access point flash with 5-GHz serial number as filename
These files are created when radar is detected on a DFS channel. The files are created with the
filename consisting of the serial number of the radio that detected the radar and include the DFS
channel on which the radar was detected. The file is used is used when the access point is reset to
ensure that the radar detected channels are not immediately selected after the reset.
filename consisting of the serial number of the radio that detected the radar and include the DFS
channel on which the radar was detected. The file is used is used when the access point is reset to
ensure that the radar detected channels are not immediately selected after the reset.
Conditions: When radar is detected on a DFS channel.
Workaround: None. This is an expected behavior. The file should not be removed.
•
CSCsl22707—A 1250 series access point using Power over Ethernet (PoE) continually resets when
connected to a Catalyst 3550 series switch.
connected to a Catalyst 3550 series switch.
Workaround: Use either a power injector or an AC power supply to provide power to the access
point, or upgrade the switch to IOS Release 12.1(19)EA1 or later and enter this CLI command to
configure the switch to continue providing power during initialization:
point, or upgrade the switch to IOS Release 12.1(19)EA1 or later and enter this CLI command to
configure the switch to continue providing power during initialization:
power inline delay shutdown (seconds) initial (seconds)
Where shutdown seconds is the amount of time that the switch continues to provide power to the
device after linkdown (between 0 and 20 seconds) and initial seconds is the initial time that the
power shutdown delay is in effect (between 0 and 300 seconds).
device after linkdown (between 0 and 20 seconds) and initial seconds is the initial time that the
power shutdown delay is in effect (between 0 and 300 seconds).
Without this command, the switch removes power immediately when a linkdown occurs on the
connected device.
connected device.
•
CSCsv82129—dot11_mgmt: bad cookie error msg appears in workgroup bridge mode running
open authentication.
open authentication.
•
CSCsv71726—1300 series root bridge with CCKM+CMIC show authentication fails.
•
CSCsw17396—Root and nonroot 1300 series bridges associate with mismatched WEP key.
•
CSCsw17391—1300 series group key update operation aborts.
•
CSCsw15978—1400 series bridge displays incorrect encryption warning messages.
Even though AES-CCM encryption is not supported on 1400 series, the following warning message
appears when user selects unsupported encryption for WPA key management: “WPA key mgmt
cipher requires one or more WPA ciphers (TKIP or AES-CCMP)”.
appears when user selects unsupported encryption for WPA key management: “WPA key mgmt
cipher requires one or more WPA ciphers (TKIP or AES-CCMP)”.
Workaround: None
•
CSCsv75779—1300 series bridge GUI association ping link test page displays a loading error.
•
CSCsv97205—Infrastructure client information is invisible on 1300 series bridge GUI.
•
CSCsw17385—1300 series GUI Station Information page displays incorrect class value.
When a root bridge and non-root bridge is configured, the station information status table on the
non-root association activity page shows “Bridge” but the root bridge class shows as “Unknown”
when it should be “Bridge”.
non-root association activity page shows “Bridge” but the root bridge class shows as “Unknown”
when it should be “Bridge”.