Cisco Cisco Aironet 350 Wireless Bridge 정보 가이드
Cisco Aironet Workgroup Bridge FAQ
Document ID: 8018
In order to get Cisco Aironet drivers, firmware, and utility software,
follow this link to the Cisco Wireless Software Center.
follow this link to the Cisco Wireless Software Center.
Contents
Introduction
What is a Workgroup Bridge?
Where can I download the latest software?
How do I upgrade the software on a Workgroup Bridge?
How can I manage the Workgroup Bridge?
Can wireless clients associate to the Workgroup Bridge?
How do I save the configurations on WorkGroup Bridge?
Can Workgroup Bridges work with other IEEE 802.11b devices?
With which devices can a Workgroup Bridge associate?
At what frequency does a Workgroup Bridge communicate?
How do I secure the data across the radio link of a Workgroup Bridge?
What EAP authentication types can the WGB use when talking to the upstream AP?
What is a Wired Equivalent Privacy (WEP) key?
What is the typical range for a Workgroup Bridge?
What is the speed of the Ethernet port of the Workgroup Bridge?
What are possible sources of interference for the radio frequency link of the Workgroup Bridge?
How do I set the Workgroup Bridge back to its factory default settings?
What security features does a Workgroup Bridge (WGB) support?
How many devices can the Workgroup Bridge support?
What are some typical applications for a Workgroup Bridge?
Can a Workgroup Bridge be used in an outdoor (building−to−building) scenario, as a bridge?
What Autonomous IOS APs can act as a WGB?
Do LWAPP APs support WGB?
What are the default settings for a WGB (350 series)?
Can an AP 340 be converted to a WGB?
Can a 340 WGB be converted to a bridge or AP?
What is the default IP address of a WGB?
Is it required that the PC IPSU installed should be on the same subnet as the Bridge in order to assign an IP
address to a WGB via IPSU?
What is meant by Bridge Loop? What are the possible causes for a Bridge Loop to occur?
What is the use of Staleout time setting?
What are the antenna options in a 350 series WGB?
What is the power specification for a WGB350?
I am unable to access Workgroup Bridges associated with access point. Why?
What are the different modulation types supported in a 350 WGB?
What is the typical range covered by a 350 series WGB?
What are the Remote configuration options supported in WGB?
I have my AP1200 act as WGB. Can I have my two Antennas on my AP to work in WGB mode?
How do I configure my AP acting as WGB to dynamically switch between parent access points based on
signal reception?
What is the maximum number of Access Points a WGB can be configured in order to attempt association?
How does an AP treats a WGB by default? Is it possible to change this default status?
Where can I download the latest software?
How do I upgrade the software on a Workgroup Bridge?
How can I manage the Workgroup Bridge?
Can wireless clients associate to the Workgroup Bridge?
How do I save the configurations on WorkGroup Bridge?
Can Workgroup Bridges work with other IEEE 802.11b devices?
With which devices can a Workgroup Bridge associate?
At what frequency does a Workgroup Bridge communicate?
How do I secure the data across the radio link of a Workgroup Bridge?
What EAP authentication types can the WGB use when talking to the upstream AP?
What is a Wired Equivalent Privacy (WEP) key?
What is the typical range for a Workgroup Bridge?
What is the speed of the Ethernet port of the Workgroup Bridge?
What are possible sources of interference for the radio frequency link of the Workgroup Bridge?
How do I set the Workgroup Bridge back to its factory default settings?
What security features does a Workgroup Bridge (WGB) support?
How many devices can the Workgroup Bridge support?
What are some typical applications for a Workgroup Bridge?
Can a Workgroup Bridge be used in an outdoor (building−to−building) scenario, as a bridge?
What Autonomous IOS APs can act as a WGB?
Do LWAPP APs support WGB?
What are the default settings for a WGB (350 series)?
Can an AP 340 be converted to a WGB?
Can a 340 WGB be converted to a bridge or AP?
What is the default IP address of a WGB?
Is it required that the PC IPSU installed should be on the same subnet as the Bridge in order to assign an IP
address to a WGB via IPSU?
What is meant by Bridge Loop? What are the possible causes for a Bridge Loop to occur?
What is the use of Staleout time setting?
What are the antenna options in a 350 series WGB?
What is the power specification for a WGB350?
I am unable to access Workgroup Bridges associated with access point. Why?
What are the different modulation types supported in a 350 WGB?
What is the typical range covered by a 350 series WGB?
What are the Remote configuration options supported in WGB?
I have my AP1200 act as WGB. Can I have my two Antennas on my AP to work in WGB mode?
How do I configure my AP acting as WGB to dynamically switch between parent access points based on
signal reception?
What is the maximum number of Access Points a WGB can be configured in order to attempt association?
How does an AP treats a WGB by default? Is it possible to change this default status?