Cisco Cisco WAP4410N Wireless-N Access Point - PoE Advanced Security 설치 가이드

• WAP4410N Wireless Access Point

• Detachable Dipole Antennas (3)

• Power Adapter

• Desktop  Stands  (2)

• 5-Foot Category 5 Ethernet Cable (1.5 meters)

• Administration Guide on CD-ROM

The WAP4410N Access Point enables you to add Wireless-N (802.11n) 
devices to your network without so much as a power plug. The WAP4410N 
allows for greater range and mobility within your wireless network while also 
allowing you to connect the wireless network to a wired environment, as 
shown in the following sample wireless network setup. 

The WAP4410N Access Point supports the 802.11n Draft 2.0 Specification by 
IEEE. It also support 802.11g and 802.11b clients in a mixed environment. This 
access point can support 802.11n connections, which are much faster than the 
earlier 802.11b/g technologies. In addition, this access point provides longer 
coverage by using multiple antennas to transmit and receive data streams in 
different directions.

Use the instructions in this Quick Start Guide to install and perform the initial 
setup of the access point. More detailed setup and configuration instructions 
are in the 

WAP4410N Wireless-N Access Point with Power Over Ethernet 

Administration Guide

, which you can get from Cisco.com, as indicated in 

Section 4, “Where to Go From Here.”

The LEDs of the access point on the front panel display information about 
network activity.

POWER LED—(Green) Lights up and remains lit when the access point is 
powered on. 

PoE LED—(Green) Lights up when the access point is powered through an 
Ethernet cable.

WIRELESS LED—(Green) Lights up when the wireless module is active on the 
access point. This LED flashes when the access point is actively sending to or 
receiving data from a wireless device. 

ETHERNET LED—(Green) Lights up when the access point successfully 
connects to a device through the Ethernet network port. This LED flashes when 
the access point is actively sending to or receiving data from one of the devices 
over the Ethernet network port. 

The ports of the access point are located on the back panel of the switch.

 

RESET Button—There are two ways to reset the access point to the factory 
default configuration. Either press the Reset button for approximately 10 
seconds or restore the defaults using the web-based utility of the access point.

ETHERNET Port—Connects to Ethernet network devices, such as a switch or 
router that may or may not support PoE.

POWER Port—Connects the access point to power using the supplied 12VDC 
power adapter.

The WAP4410N Access Point has three detachable 2dBi omni-directional 
antennas. These antennas are located on the back of the device. 

The three antennas have a base that can rotate 90 degrees when in the 
standing position. The three antennas support 3X3 “multiple in, multiple out” 
(MIMO) diversity in wireless-N mode. 

You can place the WAP4410N Access Point horizontally on its rubber feet, 
vertically in a stand, or mount it on the wall.

For desktop mounting, place the access point horizontally on a surface so it 
sits on its four rubber feet. 

To mount the WAP4410N Access Point on a wall, follow these steps.

Determine where you want to mount the WAP4410N Access Point and 
install two screws (not supplied) that are 2-15/16 inches apart 
(approximately 7.46 cm.).

With the back panel pointing up (if installing vertically), line up the 
WAP4410N Access Point so that the wall-mount crisscross slots on the 
bottom of the access point line up with the two screws.

Place the wall-mount slots over the screws and slide the WAP4410N 
Access Point down until the screws fit snugly into the wall-mount slots.

251580

Wall

mount

slots

2-15/16

To place the access point vertically in a stand, follow these steps.

Locate the left side panel of the WAP4410N Access Point.

With the two large prongs of one of the stands facing outward, insert 
the short prongs into the little slots in the WAP4410N Access Point, 
and push the stand upward until the stand snaps into place. 

Repeat this step with the other stand.

235601