Cisco Cisco WAP200E Wireless-G Exterior Access Point - PoE 관리 매뉴얼
Chapter 6
Advanced Configuration
11
Wireless-G Exterior Access Point with Power Over Ethernet
Primary DNS (Required) and Secondary DNS
•
(Optional)
Your ISP will provide you with at least one
DNS (Domain Name System) Server IP Address.
Automatic Configuration - DHCP
If you have a DHCP
server enabled on the LAN and want it to assign an IP
address to the Access Point, the select this option.
address to the Access Point, the select this option.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Help information is available on
the right side of the screen.
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Help information is available on
the right side of the screen.
Setup > Time
This allows you to change the Access Point’s time settings.
The correct time setting can help the administrator to
search the system log to identify problems.
The correct time setting can help the administrator to
search the system log to identify problems.
Setup > Time
Time
You can set the time either manually or automatically
from a time server if the Access Point can access the public
Internet. The default is to set the time Automatically.
from a time server if the Access Point can access the public
Internet. The default is to set the time Automatically.
Manually
Select this option to set the date and time
manually.
Automatically
Select this option and time zone. The
Access Point will contact the public time server to get the
current time.
current time.
Automatically adjust clock for daylight saving
•
changes
Select this option if you are in using the
Access Point in a location that observes daylight saving
time.
time.
User Defined NTP Server
•
Enable this option if you
have set up local NTP server. Default is Disabled.
NTP Server IP
•
Enter the IP address of user defined
NTP Server.
Change these settings as described here and click Save
Settings to apply your changes, or click Cancel Changes
Settings to apply your changes, or click Cancel Changes
to cancel your changes. Help information is available on
the right side of the screen.
the right side of the screen.
Wireless > Basic Wireless Settings
Change the basic wireless network settings on this screen.
The Access Point can connect to up to four wireless
networks (SSIDs) at the same time, so this screen offers
settings for up to four different SSIDs. Each SSID owns its
own MAC address on this Access Point.
The Access Point can connect to up to four wireless
networks (SSIDs) at the same time, so this screen offers
settings for up to four different SSIDs. Each SSID owns its
own MAC address on this Access Point.
Wireless > Basic Wireless Settings
Basic Settings
Configure the Wireless Network basic attributes for the
entire system and for each SSID.
entire system and for each SSID.
Wireless Network Mode
Select one of the following
modes. The default is Mixed.
Disable
•
To disable wireless connectivity completely.
This might be useful during system maintenance.
B-Only
•
All the wireless client devices can be
connected to the Access Point at Wireless-B data rates
with maximum speed at 11Mbps.
with maximum speed at 11Mbps.
G-Only
•
Wireless-G client devices can be connected at
Wireless-G data rates with maximum speed at 54Mbps.
Wireless-B clients cannot be connected in this mode.
Wireless-B clients cannot be connected in this mode.
Mixed
•
Both Wireless-B and Wireless-G client devices
can be connected at their respective data rates.
Wireless-G devices can be connected at Wireless-G
data rates.
Wireless-G devices can be connected at Wireless-G
data rates.
Wireless Channel
Select the appropriate channel to be
used among your Access Point and your client devices.
When Auto is selected, your Access Point will select the
channel with the lowest amount of wireless interference
while the system is powering up. Auto channel selection
will start when you click Save Settings button, it will take
several seconds to scan through all the channels to find
the best channel. The default setting is Auto.
When Auto is selected, your Access Point will select the
channel with the lowest amount of wireless interference
while the system is powering up. Auto channel selection
will start when you click Save Settings button, it will take
several seconds to scan through all the channels to find
the best channel. The default setting is Auto.