Cisco Cisco WAP2000 Wireless-G Access Point - PoE 설치 가이드

• Wireless-G Access Point with Power Over Ethernet

• Detachable Dipole Antennas (2)

• Power Adapter

• Ethernet Cable

• CD-ROM

• Quick Start Guide

Thank you for choosing the WAP2000

Wireless-G Access Point with Power 

Over Ethernet. The access point features RangeBooster technology that is 
compatible with standard 802.11g but with a range up to two times further and 
throughput up to 35 percent faster. Unlike ordinary wireless technologies that 
are hampered by wireless signals that reflect off walls, ceilings, and other 
objects, RangeBooster uses these multiple signals with two smart receivers at 
each end (router or access point and client adapter) to boost range and 
throughput speeds. As a result, a RangeBooster solution reduces or eliminates 
wireless signal dead spots in offices and other buildings so users can connect 
to the network in more areas. 

This guide describes how to physically install your WAP2000 and how to set 
up a basic configuration by using the configuration utility. 

Before you begin the installation, make sure that you have the following 
equipment and services: 

• Tools for installing the hardware

• Category 5e Ethernet cable

• PC with Microsoft Internet Explorer (6.0 or later) or Mozilla Firefox for using 

the web-based system management tools

• A Cisco Small Business Power over Ethernet (PoE) switch or a switch and a 

802.3af compliant power injector

• (

Recommended

) Uninterruptible Power Supply (UPS) to provide backup 

power to essential devices

This section describes the external features of the WAP2000.

POWER—(Green) Lights up when the access point is powered on.

PoE—(Green) Lights up when the access point is powered through an 
Ethernet cable. 

WIRELESS—(Green) Lights up when the wireless module is active on the 
access point. The LED flashes when the access point is actively sending or 
receiving data from a wireless device.

Ethernet—(Green) Lights up when the access point successfully connects to 
a device through the Ethernet network port. This LED flashes when the access 
point is actively sending to or receiving data from one of the devices over the 
Ethernet network port.

Antenna Ports—The access point has two antenna ports for connecting 
detachable 3 dBi omnidirectional antennas. Adjust the two antennas so that 
they form a 90 degree angle for best MIMO range performance. 

RESET Button—There are two ways to reset the access point to the factory 
default configuration. Either press the Reset button for more than ten seconds 
or restore the defaults using the web-based utility of the access point. If you 
press the Reset button for less than ten seconds, the access point will simply 
reboot.

ETHERNET Port—Connects to Ethernet network devices, such as a switch or 
router. The access point can be powered using Power over Ethernet. 

POWER Port—Connects the access point to power using the supplied power 
adapter. Use this option if your switch or router doesn’t support Power over 
Ethernet.

Security Slots—The security slots can be utilized to attach a lock to the 
access point.

You can place your WAP2000 on a desktop or mount it on a wall.

• Ambient  Temperature—To prevent the WAP2000 from overheating, do not 

operate it in an area that exceeds an ambient temperature of 131°F (55°C).

• Air  Flow—Be sure that there is adequate air flow around the WAP2000.

• Mechanical Loading—Be sure that the WAP2000 is level and stable to 

avoid any hazardous conditions.

• Power Outlet—Choose a location that is within reach of a power outlet.

The WAP2000 can be mounted either vertically or horizontally.

Determine where you want to mount the access point and install two 
screws (not supplied) into the wall for either vertical or horizontal 
placement. 

For horizontal placement, orient the access point as shown:

For vertical placement, orient the access point as shown:

276237

Wall

mount

slots

5-7/8˝

276238

Wall

mount

slots

4-1/4˝