Cisco Cisco Aironet 1200 Access Point 릴리즈 노트
20
Release Notes for Cisco Aironet Access Points for Cisco IOS Release 12.3(8)JEC1
OL-16115-01
Caveats
•
CSCsl58293—1242 access point failed to associate using Authentication Shared
1242 fails to associate via authentication shared using 12.4(10b)JA release image. The same
behavior occurs on C3202/C3205 Wireless MICs when they try to associate via authentication
shared on their 12.4(3)JK release images.
behavior occurs on C3202/C3205 Wireless MICs when they try to associate via authentication
shared on their 12.4(3)JK release images.
Conditions—Configure AP1242 (or C3202/C3205 Wireless MICs) to be root and client devices with
authentication method to be authentication shared under the SSID configuration.
authentication method to be authentication shared under the SSID configuration.
Workaround—Configure a more secure method by using authentication open with WPA-PSK key
management.
management.
•
CSCsl76740—Access point crashes after SNMP query
An Access point may crash when an SNMP query is performed over an interface where a QoS policy
is configured.
is configured.
Workaround: None.
•
CSCsm24495—Configuration change for adding data rate does not reflect in running config
•
CSCsm31801—TKIP+ WPAV2+CCKM does not work
When combination of authentication key-management WPA version 2 CCKM + encryption mode
ciphers TKIP is configured, an association failure occurs.
ciphers TKIP is configured, an association failure occurs.
Workaround—None.
•
CSCsm34905—Wrong dynamic VLAN assigned after re-authentication
After re-association, Wireless-Client gets access to wrong VLAN (Different VLAN then assigned
via AAA)
via AAA)
Conditions—IOS AP, VLAN assignment via AAA, WPAv2 (AES encryption).
Workaround—Disable PMK caching on wireless client site.
•
CSCsm38303—Coverage display on WLSE does not display correctly
The problem occurs when the coverage display in the location manager on WLSE changes to red,
causing an incorrect display. This issue seems to occur on software versions later than 12.4(3g)JA.
It does not appear to occur on older versions such as 12.3(11)JA2. The problem has been observed
on the following platforms and versions:
causing an incorrect display. This issue seems to occur on software versions later than 12.4(3g)JA.
It does not appear to occur on older versions such as 12.3(11)JA2. The problem has been observed
on the following platforms and versions:
–
CWWLSE-1133-K9,1130 / version 2.15
–
- AP1130AG: 12.3(11)JA, 12.4(10b)JA
–
- AP1240AG: 12.4(3g)JA, 12.4(10b)JA
Workaround—Use an older access point image.
•
CSCsm80730—1240 access point does not send a re-association response to client
When a client tries to roam from one access point to another, during one of the roams the client sends
a re-association request, the WDS 1240 Responds with an ACK but does not send a re-association
response. The client then sends a deauthentication request and tries to do a full reauthentication.
a re-association request, the WDS 1240 Responds with an ACK but does not send a re-association
response. The client then sends a deauthentication request and tries to do a full reauthentication.
•
CSCsm97867—Autonomous workgroup bridge does not send out bad MIC on broadcast frame
The autonomous workgroup bridge is used to generate bad MIC TKIP frames for testing access
points for proper MIC countermeasures operation. However, when a radio is configured as a
workgroup bridge or a repeater, it will not send out the bad MIC frame on a broadcast packet. The
radio sends the bad MIC out if it is in root mode, but not workgroup bridge or repeater mode.
points for proper MIC countermeasures operation. However, when a radio is configured as a
workgroup bridge or a repeater, it will not send out the bad MIC frame on a broadcast packet. The
radio sends the bad MIC out if it is in root mode, but not workgroup bridge or repeater mode.
This issue occurs on versions 12.3(8)JA, 12.3(11)JA, 12.4(3g)JA, and 12.4(10b)JA.
This issue occurs on versions 12.3(8)JA, 12.3(11)JA, 12.4(3g)JA, and 12.4(10b)JA.