Cisco Cisco Digital Service Access Node (DSAN) 8200 설치 가이드
Chapter 5 CLI Diagnostics
124
OL-29943-01
Field Name
Error on Bootup
eCM (DOCSIS) IP
Address
Address
eCM Address
eCM Address
eCM Address
eCM Address
eCM Address
VCT ID (Hub ID)
Not Available
Expected Hub ID
(e.g. 0x0001)
(e.g. 0x0001)
Expected Hub ID
(e.g. 0x0001)
(e.g. 0x0001)
Expected Hub ID
(e.g. 0x0001)
(e.g. 0x0001)
Expected Hub ID
(e.g. 0x0001)
(e.g. 0x0001)
eCM State
Two Way
Lost
Communication
Scanning for
DOCSIS
Downstream
Channel
Communication
Scanning for
DOCSIS
Downstream
Channel
Two Way
Two Way
Two Way
TFTP Server Name
[an IP Address]
[an IP Address]
TFTP Address
TFTP Address
TFTP Address
TFTP Address
TFTP Address
Config File Name
Expected Name -
"Loaded"
"Loaded"
Expected Name -
"Loaded"
"Loaded"
Expected Name -
"Loaded"
"Loaded"
Expected Name -
"Loaded"
"Loaded"
Expected Name -
"Loaded"
"Loaded"
Diag Page 5: Tuner Status
Tuner Locked
"Locked" for all
demodulators
demodulators
"U" (Unlocked)
for all
demodulators
for all
demodulators
"U" (Unlocked) for
a block of
demodulators
a block of
demodulators
"Locked" for all
demodulators
demodulators
"Locked" for all
demodulators
demodulators
Diag Page 7: Demodulator Status
Status
"Locked" for all
demodulators
demodulators
"Unlocked" for
all demodulators
all demodulators
"Unlocked" for a
block of
demodulators
block of
demodulators
"Locked" for all
demodulators
demodulators
"Locked" for all
demodulators
demodulators
Diag Page 9.x: Service Map Status
Status
"OK" for all
channels
channels
"Error" for all
channels
channels
"Error" for one or
more channels
more channels
"Error" for one or
more channels
more channels
"Error" for one or
more channels
more channels
Diag page 10.x: Channel Configuration
Status
"OK" for all
channels
channels
"QAM Demod
Not Locked" for
all channels
Not Locked" for
all channels
"QAM Demod
Not Locked" for
all channels in
error
Not Locked" for
all channels in
error
"Wideband
Frequency
Remap Error" for
all channels in
error
Frequency
Remap Error" for
all channels in
error
"Source ID Not
Found" for all
channels in error;
QAM Mode field
states "Invalid
QAM Mode 0"
Found" for all
channels in error;
QAM Mode field
states "Invalid
QAM Mode 0"
* N/A if not used.
** Error conditions will persist in CLI for several minutes after RF cable connection is restored.
** Error conditions will persist in CLI for several minutes after RF cable connection is restored.
Error on Bootup
Field Name
More than 16
QAMs Defined
QAMs Defined
Diag Page 1: DSAN Status
Current Alarms
1
DOCSIS State
Connected - Idle
Provisioning State Idle
Remap State
Channel
Remapped
Remapped
Tuner A
Locked or N/A *