Cisco Cisco 1 GHz GainMaker Amplifier 데이터 시트
© 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 6
Ordering Information
The Cisco GainMaker HGBT System Amplifier is available in a wide variety of configurations. Table 7 contains the
configured PIDs for the High Gain Balanced Triple Amplifiers. Table 8 and Table 9 contain ordering information for
required and optional accessories. Consult with your Cisco account representative, customer service
representative, or system engineer to determine the best configuration for your particular application.
Table 7.
Cisco GainMaker High Gain Balanced Triple (HGD) Amp Configurations
Cisco GainMaker 1.2-GHz HGD Amp Configurations
Part Number for Ordering
42/54 MHz Split
GMSA 1.2 GHz, HGBT,42/54, CB, PS, CTD HSG, TPA, Thermal
GMSATS4THXXXXXXXXX
GMSA 1.2 GHz, HGBT,42/54, CB, Launch Amp, Thermal
GMSATS4TXXXXXXXXXX
GMSA 1.2 GHz, HGBT,42/54, CB, PS, CTD HSG, TPA, QAM AGC 711 MHz
GMSATS45HXXXXXXXXX
GMSA 1.2 GHz, HGBT,42/54, CB, Launch Amp, QAM AGC 711 MHz
GMSATS45XXXXXXXXXX
Table 8.
Required Accessories
Required Accessories
Part Number
Plug-in Pads (attenuators): Available in 1.0 dB steps from 0 to 20 dB
● 1 required for forward input
● 1 required for AGC, if applicable
● 1 required for AGC, if applicable
*
● 4 required for reverse (3 input, 1 output)
*
To determine AGC pad value, subtract 34 dB from the design value main port RF output
level at the AGC pilot frequency.
GM-PAD-1.2G-00= and
GM-PAD-1.2G-1.0 sequentially through
GM-PAD-1.2G-20.0=
Plug-in Forward Cable Equalizer: Available in 1.5 dB steps from 0 to 30 dB at 1002 MHz
● 1 required for forward input
GM-EQC-1.2G-0= and
GM-EQC-1.2G-1.5 sequentially through
GM-EQC-1.2G-30=
Plug-in Reverse Cable Equalizer: Available in 1 dB steps from 0 to 12 dB at 42 MHz
● 1 required for reverse output, unless design value is 0 dB (0 dB EQ is provided)
712719 (0 dB) and
589628 (1dB) sequentially thru 589639 (12 dB)
– 40 MHz
– 40 MHz
589736 (1 dB) sequentially thru 589747 (12
dB)
dB)
– 65 MHz
4036769 (1 dB) sequentially thru 4036780 (12
dB)
dB)
– 85 MHz
GM-EQREV-204M-1= (1 dB) sequentially thru
GM-EQREV-204M-12= (12 dB)
GM-EQREV-204M-12= (12 dB)
– 204 MHz
The optional accessories listed in Table 8 can be ordered separately.
Table 9.
Optional Accessories
Optional Accessories
Part Number
24V Power Supply for Cisco GainMaker HGD
GM-PS-HO=
230 VAC Crowbar Surge Protector (plug-in, one per station)
Plug-in Inverse Equalizer: Simulates cable equivalent tilts (creates tilt opposite that of
equalizers). Use in place of forward input EQ as needed to maintain proper output tilt in
short spaced locations. Available in 1.5dB cable-equivalent steps from 1.5 to 21.0dB
equalizers). Use in place of forward input EQ as needed to maintain proper output tilt in
short spaced locations. Available in 1.5dB cable-equivalent steps from 1.5 to 21.0dB
GM-EQIN-1.2G-1.5= sequentially thru GM-
EQIN-1.2G-21=
EQIN-1.2G-21=
Long Reach Test Point Adapter
562580
Cisco GainMaker SA HGBT Split Kit 85/105 MHz (PKG OF 10)
TBD
Status Monitoring Transponder
Refer to the Cisco GainMaker Status
Monitoring Transponder Data Sheet.
Monitoring Transponder Data Sheet.