Samsung SCX-4725FN 사용자 설명서
13.4
<Troubleshooting>
[Low Heat Error]
There is a problem
in the fuser unit.
in the fuser unit.
Unplug the power cord
and plug it back in. If the
problem persists, please
call for service.
and plug it back in. If the
problem persists, please
call for service.
[LSU Error]
A problem has
occurred in the LSU
(Laser Scanning
Unit).
occurred in the LSU
(Laser Scanning
Unit).
Unplug the power cord
and plug it back in. If the
problem persists, please
call for service.
and plug it back in. If the
problem persists, please
call for service.
[No Answer]
The receiving fax
machine has not
answered after
several redial
attempts.
machine has not
answered after
several redial
attempts.
Try again. Make sure that
the receiving machine is
operational.
the receiving machine is
operational.
[No Paper]
Add Paper
Add Paper
The paper in the tray
has run out.
has run out.
Load paper in the tray.
See page 5.5.
See page 5.5.
[Over Heat]
There is a problem
in the fuser unit.
in the fuser unit.
Unplug the power cord
and plug it back in. If the
problem persists, please
call for service.
and plug it back in. If the
problem persists, please
call for service.
Open Heat Error
There is a problem
in the fuser unit.
in the fuser unit.
Unplug the power cord
and plug it back in. If the
problem persists, please
call for service.
and plug it back in. If the
problem persists, please
call for service.
[Paper Jam 0]
Open/Close Door
Open/Close Door
Paper has jammed
in the feeding area
of the tray.
in the feeding area
of the tray.
[Paper Jam 1]
Open/Close Door
Open/Close Door
Paper has jammed
in the fuser area.
in the fuser area.
Clear the jam. See page
13.2.
13.2.
[Paper Jam 2]
Check Inside
Check Inside
Paper has jammed
in the paper exit
area.
in the paper exit
area.
Clear the jam. See page
13.2.
13.2.
[Stop Pressed]
Stop/Clear has
been pressed during
a fax transmission.
been pressed during
a fax transmission.
Try again.
Add Paper &
Press Start
Press Start
You have selected
Manual Feeder for
Source in the printer
properties.
Manual Feeder for
Source in the printer
properties.
Load a sheet of paper
into the manual tray and
press Start to start
feeding.
If you have multiple
pages to be printed, this
message appears again.
Load the next sheet and
press Start.
into the manual tray and
press Start to start
feeding.
If you have multiple
pages to be printed, this
message appears again.
Load the next sheet and
press Start.
Message
Meaning
Suggested solutions
Cancel?
1:Yes 2:No
1:Yes 2:No
Your machine’s
memory has
become full while
trying to store an
original into memory.
memory has
become full while
trying to store an
original into memory.
To cancel the fax job,
press 1 to select Yes.
If you want to send those
pages that have been
successfully stored,
press 2 to select No. You
should send the
remaining pages later,
when memory is
available.
press 1 to select Yes.
If you want to send those
pages that have been
successfully stored,
press 2 to select No. You
should send the
remaining pages later,
when memory is
available.
Document Jam
The loaded original
has jammed in the
ADF.
has jammed in the
ADF.
Clear the jam. See page
13.1.
13.1.
Enter Again
You entered an
unavailable data.
unavailable data.
Enter the correct data
again.
again.
Group Not
Available
Available
You have tried to
select a group dial
number where only
a single location
number can be
used.
select a group dial
number where only
a single location
number can be
used.
Use a speed dial number
or dial a number
manually using the
number keypad.
or dial a number
manually using the
number keypad.
Line Busy
The receiving fax
machine did not
answer or the line is
already engaged.
machine did not
answer or the line is
already engaged.
Try again after a few
minutes.
minutes.
Load Document
You have attempted
to set up a copy or
fax operation with no
document loaded
into the ADF.
to set up a copy or
fax operation with no
document loaded
into the ADF.
Load a document into the
ADF and try again.
ADF and try again.
Memory Dial Full
The fax jobs queue
in the memory is full.
in the memory is full.
Cancel unnecessary fax
jobs in the memory.
jobs in the memory.
Memory Full
The memory is full.
Delete unnecessary fax
jobs and retransmit after
more memory becomes
available. Alternatively,
split the transmission into
more than one operation.
jobs and retransmit after
more memory becomes
available. Alternatively,
split the transmission into
more than one operation.
Not Assigned
The speed dial
number you tried to
use has no number
assigned to it.
number you tried to
use has no number
assigned to it.
Enter the number
manually using the
number keypad.
manually using the
number keypad.
Operation Not
Assigned
Assigned
You are in the Add
Page/Cancel Job
operation, but there
are no jobs stored.
Page/Cancel Job
operation, but there
are no jobs stored.
Check the display to see
if there are any
scheduled jobs.
if there are any
scheduled jobs.
Message
Meaning
Suggested solutions