Samsung AR24MVFSBWKXME 설치 가이드

Installation manual

AR✴✴HVSS✴✴, AR✴✴JVFS✴✴, AR✴✴KVFS✴✴, AR✴✴KVFN✴✴,
AR✴✴MVFS✴✴, AR✴✴MVFN✴✴

Safety Information on

Installation

Carefully follow the precautions listed below because

they are essential to guarantee the safety of both the air

conditioner and the workers.

• Always disconnect the air conditioner from the power

supply before servicing it or accessing its internal

components.

• Verify that installation and testing operations are

performed by qualified personnel.

• Verify that the air conditioner is not installed in an easily

accessible area.

General information

• Carefully read the content of this manual before installing

the air conditioner and store the manual in a safe place in

order to be able to use it as reference after installation.

• For maximum safety, installers should always carefully

read the following warnings.

• Store the operation and installation manual in a safe

location and remember to hand it over to the new owner if

the air conditioner is sold or transferred.

• This manual explains how to install an indoor unit with a

split system with two SAMSUNG units. The use of other

types of units with different control systems may damage

the units and invalidate the warranty. The manufacturer

shall not be responsible for damages arising from the use

of non compliant units.

• This product has been determined to be in compliance

with the Low Voltage Directive (2006/95/EC) and the

Electromagnetic Compatibility Directive (2004/108/EC) of

the European Union.

• The manufacturer shall not be responsible for damage

originating from unauthorised changes or the improper

connection of electric and requirements set forth in the

“Operating limits” table, included in the manual, shall

immediately invalidate the warranty.

• The air conditioner should be used only for the applications

for which it has been designed: the indoor unit is not

suitable to be installed in areas used for laundry.

• Do not use the units if damaged. If problems occur, switch

the unit off and disconnect it from the power supply.

• In order to help prevent electric shocks, fires or injuries,

always stop the unit, disable the protection switch and

contact SAMSUNG’s technical support if the unit produces

smoke, if the power cable is hot or damaged or if the unit

is very noisy.

• Always remember to inspect the unit, electric connections,

refrigerant tubes and protections regularly. These

operations should be performed by qualified personnel

only.

• The unit contains moving parts, which should always be

kept out of the reach of children.

• Do not attempt to repair, move, alter or reinstall the unit.

If performed by unauthorised personnel, these operations

may cause electric shocks or fires.

• Do not place containers with liquids or other objects on

the unit.

• All the materials used for the manufacture and packaging

of the air conditioner are recyclable.

• The packing material and exhaust batteries of the remote

control (optional) must be disposed of in accordance with

current laws.

• The air conditioner contains a refrigerant that has to be

disposed of as special waste. At the end of its life cycle, the

air conditioner must be disposed of in authorised centres

or returned to the retailer so that it can be disposed of

correctly and safely.

Installation of the unit

• IMPORTANT: When installing the unit, always remember

to connect first the refrigerant tubes, then the electrical

lines. Always disassemble the electric lines before the

refrigerant tubes.

• Upon receipt, inspect the product to verify that it has not

been damaged during transport. If the product appears

damaged, DO NOT INSTALL it and immediately report

the damage to the carrier or retailer (if the installer or the

authorised technician has collected the material from the

retailer.)

• After completing the installation, always carry out a

functional test and provide the instructions on how to

operate the air conditioner to the user.

• Do not use the air conditioner in environments with

hazardous substances or close to equipment that release

free flames to avoid the occurrence of fires, explosions or

injuries.

• Our units must be installed in compliance with the spaces

indicated in the installation manual to ensure either

accessibility from both sides or ability to perform routine

maintenance and repairs. The units’ components must be

accessible and that can be disassembled in conditions of

complete safety either for people or things. For this reason,

where it is not observed as indicated into the Installation

Manual, the cost necessary to reach and repair the unit

(in safety, as required by current regulations in force) with

slings, trucks, scaffolding or any other means of elevation

won’t be considered in-warranty and will be charged to

end user.

• When installing the outdoor unit at the seaside, make

sure that it is not directly exposed to sea breeze. If you

cannot find an adequate place free from direct sea breeze,

construct a protection wall or a protective fence.

–

Install the outdoor unit in a place (such as near buildings

etc.) where it can be protected from sea breeze. Failure to

do so may cause a damage to the outdoor unit.

Sea

Sea breeze

Outdoor unit

Sea breeze

Sea

• If you cannot avoid installing the outdoor unit at the seaside,

construct a protection wall around to block the sea breeze.

• Construct a protection wall with a solid material such as

concrete to block the sea breeze. Make sure that the height

and the width of the wall are 1.5 times larger than the size

of the outdoor unit. Also, secure a space larger than 600

mm between the protection wall and the outdoor unit for

exhausted air to ventilate.

Sea

Sea breeze

Outdoor unit

Protection wall

Outdoor unit

Protection wall

• Install the unit in a place where water can drain smoothly.
• If you have any difficulty finding installation location as

prescribed above, contact your manufacturer for details.

• Be sure to clean the sea water and the dust on the heat

exchanger of the outdoor unit and apply a corrosion inhibitor

on it. (At least once in a year.)

Power supply line, fuse, or circuit

breaker

• Always make sure that the power supply is compliant with

current safety standards. Always install the air conditioner in

compliance with current local safety standards.

• Always verify that a suitable grounding connection is

available.

• Verify that the voltage and frequency of the power supply

comply with the specifications and that the installed power

is sufficient to ensure the operation of any other domestic

appliance connected to the same electric lines.

• Always verify that the cut-off and protection switches are

suitably dimensioned.

• Verify that the air conditioner is connected to the power

supply in accordance with the instructions provided in the

wiring diagram included in the manual.

• Always verify that electric connections (cable entry, section

of leads, protections…) are compliant with the electric

specifications and with the instructions provided in the

wiring scheme. Always verify that all connections comply

with the standards applicable to the installation of air

conditioners.

• Be sure not to perform power cable modification, extension

wiring, and multiple wire connection.

–

It may cause electric shock or fire due to poor connection,

poor insulation, or current limit override.

–

When extension wiring is required due to power line

damage, refer to "Step 2.4 Optional: Extending the power

cable" in the installation manual.

Preparation

Step 1.1 Choosing the installation

location

Overview of installation location requirements

100 mm or more

Outdoor

Unit

Indoor Unit

Cut insulation to have

rainwater drained

Outer wall

Drain hose hole

You can select the direction of

draining (left or right).

Maximum pipe height: 15 m

Maximum pipe length: 30 m

125 mm or

The actual units may look different from the

images depicted here.

Make a U-trap (A) on the pipe

(which is connected to the indoor

unit) at outer wall and cut the

bottom part of the insulation

(about 10 mm) to prevent

rainwater from getting inside

through the insulation.

Make at least one round to reduce

noise and vibration.

CAUTION

• Comply with the length and height limits described in the

figure above.

Minimum clearances for the outdoor unit

Wall

Minimum clearance in mm

300

600

Air flow direction

Side view

Top view

When installing 1 outdoor unit (6 cases)

(Unit: mm)

300

1500

300

150

600

1500

2000

500

300

1500

(Unit : m)

Model

Pipe length

Pipe height

Minimum

Maximum

✴✴

09/12✴✴ME/TC

✴✴

10/13✴✴UN

✴✴

09/12✴✴SS

✴✴

18/24✴✴ME/UN

✴✴

18/24✴✴SS/TC

When installing more than 1 outdoor unit (5 cases)

(Unit: mm)

1500

600

3000

200

3000

300

1500

600

1500

300

600

500

300

500

300

CAUTION

• If the outdoor unit is installed with any insufficient

clearance, it may generate sound and affect the whole

product.

• Be sure to install the outdoor unit in a level place where its

vibration does not affect the whole product.

Step 1.2 Unpacking

Unpacking the indoor unit

1  Open the indoor unit package.
2  Remove the left and right cushions.
3  Pull out the unit from the package.

Unpacking the outdoor unit

1  Remove the package.
2  Remove the top cushion.
3  Pull out the unit from the bottom cushion.

Step 1.3 Checking and preparing

accessories and tools

Accessories

Accessories in the indoor unit package

Installation plate (1)

✴✴

10✴✴UN

Installation plate (1)

✴✴

13/18✴✴UN

Installation plate (1)

✴✴

09/12✴✴

✴✴

18✴✴ME

Installation plate (1)

✴✴

18✴✴SS/TC

✴✴

24✴✴

Remote control (1)

Remote control holder (1)

Remote control battery (2)

Users Manual (1)

Installation Manual (1)

Cap screw (2)

Installation Manual (1)

Optional accessories

Insulated assembly pipe,

Ø 6.35 mm (1)

Insulated assembly pipe,

Ø 9.52 mm (1)

✴✴

09/10/12/13✴✴

Insulated assembly pipe,

Ø 12.70 mm (1)

✴✴

18✴✴

Insulated assembly pipe,

Ø 15.88 mm (1)

✴✴

24✴✴

Drain Hose, 2 m long (1)

Pipe clamp B (3)

Pipe clamp A (3)

Vinyl tape (2)

PE T3 foam tube insulation (1)

Putty 100 g (1)

Drain plug (1)

M4 x 25 tapped screw (6)

Cement nail (6)

4-wire assembly cable (1)

✴✴

09/12✴✴TC

✴✴

09/12/18✴✴ME

✴✴

10/13/18✴✴UN

3-wire power cable (1)

✴✴

18/24✴✴TC

✴✴

09/12/18/24✴✴SS

3-wire assembly cable (1)

✴✴

18/24✴✴TC

✴✴

24✴✴ME/UN

✴✴

09/12/18/24✴✴SS

2-wire assembly cable (1)

✴✴

18/24✴✴TC

✴✴

09/12/18/24✴✴SS

1-wire assembly cable (1)

✴✴

24✴✴ME/UN

Accessories in the outdoor unit package

Rubber leg (4)

NOTE

• A flare nut is attached to the end of each pipe of an

evaporator or a service port. Use flare nuts when connecting

the pipes.

• Wire assembly cables are optional. If they are not supplied,

use standard cables.

• The drain plug and the rubber legs are included only when

the air conditioner is supplied without assembly pipes.

• If these accessories are supplied, they are in the accessory

package or outdoor unit package.

Tools

General tools

• Vacuum pump

(Backward flowing

prevention)

• Manifold gauge
• Stud finder
• Torque wrench
• Pipe cutter
• Reamer

• Pipe bender
• Spirit level
• Screwdriver
• Spanner
• Drill
• L-wrench
• Measuring tape

Tools for test operation
• Thermometer
• Resistance meter
• Electroscope

Step 1.4 Drilling a hole through the

wall

Before fixing the installation plate to a wall and then fixing

the indoor unit to the installation plate, a window frame, or

a gypsum board, you must determine the position of a hole

(with 65 mm inner diameter) through which the pipe bundle

(consisting of power and communication cables, refrigerant

pipes, and drain hose) will pass and then drill that hole.

1 Determine the position of a 65 mm hole in consideration

of the possible directions of the pipe bundle and the

minimum distances between the hole and the installation

plate.

Right

Left

Rear right or left

Bottom right

CAUTION

• If changing the pipe direction from left to right, do not

drastically bent it but slowly turn it in the opposite

direction as shown. Otherwise, the pipe may be damaged

in the process.

<Minimum distances between the hole and the

installation plate>

Pipe bundle hole

2 Drill the hole.

CAUTION

• Be sure to drill only one hole.
• Make sure that the hole slants downwards so that the

drain hose slants downwards to drain water well.

Wall

Drain hose

Indoor unit

Step 1.5 Taping the pipes, cables, and

drain hose

1 Wrap foam insulation on parts without insulation on the

ends of the refrigerant pipes, as shown in the figure. This

wrapping minimises condensation problem.

Insulation

Refrigerant pipes

2 Wind the refrigerant pipes, power cable,

communication cable and drain hose with vinyl
tape to make a pipe bundle.

Refrigerant pipes

(assembly pipe)

Installation plate

Vinyl tape

Drain hose

Power and communication cables

(assembly cable)

Indoor Unit Installation

Please scan this QR code for detail

video of indoor unit installation.

Step 2.1 Disassembling the cover

panel

1 Remove the cap screws, then the screws.

(Unit : mm)

Model

✴✴

10✴✴UN

✴✴

09/12✴✴

✴✴

13✴✴UN

120

✴✴

18✴✴ME/UN

190

✴✴

18✴✴TC/SS

✴✴

24✴✴

110

Pipe bundle hole: Ø 65 mm

Cap screw

Screw

Phillips screwdriver

Flat-head screwdriver

2 Unlock the side hooks ( , ), then centre hooks ( ).

Then unlock the bottom hooks ( ) to pull out the cover
panel.

Centre hook (A)

Bottom/Side hook (B/C)

Step 2.2 Disassembling the

installation plate

Step 2.3 Connecting the power and

communication cables (assembly

cable)

Control box

1(L)2(N)

F1 F2

• When performing electrical and earthing works, be sure

to comply with the 'technical standards of electrical

installations' and the 'wiring regulations' in the local

regulations.

• Tighten the terminal block screw to 1.2-1.8 N•m (1.2-1.8

kgf•cm).

NOTE

• Each wire is labelled with the corresponding terminal

number.

• Use shield cable (Category 5; less than 50pF/m) for noisy

environmental site.

• Power supply cords of parts of appliances for outdoor

use shall not be lighter than polychloroprene sheathed

flexible cord. (Code designation IEC: 60245 IEC66/CENELEC:

H07RN-F, IEC: 60245 IEC57/CENELEC: H05RN-F, IEC: 60227

IEC53/CENELEC: H05VV-F)

• Power & Communication cable shall not exceed 30m.

CAUTION

• For the terminal block wiring, use a wire with a ring terminal

socket only. Regular wires without a ring terminal socket

may become a hazard due to overheating of the electrical

contact during installation.

• If you need to extend the pipe, be sure to extend the cable,

too. The maximum length of each of the cable and pipe

used should not exceed 15 meters (✴✴09/12/18✴✴) and 20

metres (✴✴24✴✴).

• Do not connect two or more different cables to extend the

length. This connection may cause fire.

• Each circular terminal must match the size of its

corresponding screw in the terminal block.

• After connecting the cables, make sure that terminal

numbers on the indoor and outdoor units match.

• Ensure that power and communication cables are

separated, they must not be in the same cable.

WARNING

• Connect the wires firmly so that wires cannot be pulled

out easily. (If they are loose, it could cause burn-out of the

wires.)

Step 2.4 Optional: Extending the

power cable

1 Prepare the following tools.

Tools

Spec

Shape

Crimping

pliers

MH-14

Connection

sleeve (mm)

20xØ6.5 (HxOD)

Insulation

tape

Width 19 mm

Contraction

tube (mm)

70xØ8.0 (LxOD)

2 As shown in the figure, peel off the shields from the rubber

and wire of the power cable.
• Peel off 20 mm of cable shields from the pre-installed

tube.

CAUTION

• For information about the power cable specifications for

indoor and outdoor units, refer to the installation manual.

• After peeling off cable wires from the pre-installed tube.

Insert a contraction tube.

Before

connecting

Correct

Upside

down

Damaged

Non-

circular

After

connecting

Correct

Upside

down

Non-fitted

(Front view) (Side view)

Power cable

Pre-installed tube for the power cable

(Unit: mm)

120

180

3 Insert both sides of core wire of the power cable into the

connection sleeve.
• Method 1: Push the core wire into the sleeve from both

sides.

• Method 2: Twist the wire cores together and push it into

the sleeve.

Connection sleeve

Method 1

Method 2

4 Using a crimping tool, compress the two points and flip it over

and compress another two points in the same location.
• The compression dimension should be 8.0.

Compression

dimension

• After compressing it, pull both sides of the wire to make

sure it is firmly pressed.

Compress it 4 times.

5 mm

Compress it 4 times.

5 mm

Method 1

Method 2

5 Wrap it with the insulation tape twice or more and

position your contraction tube in the middle of the

insulation tape.

Three or more layers of insulation are required.

Method 1

Method 2

Insulation tape

40 mm

35 mm

Insulation tape

6 Apply heat to the contraction tube to contract it.

Contraction tube

7 After tube contraction work is completed, wrap it with the

insulation tape to finish.

Insulation tape

CAUTION

• Make sure that the connection parts are not exposed to

outside.

• Be sure to use insulation tape and a contraction tube made

of approved reinforced insulating materials that have the

same level of withstand voltage with the power cable.

(Comply with the local regulations on extensions.)

WARNING

• In case of extending the electric wire, please DO NOT use a

round-shaped pressing socket.

–

Incomplete wire connections can

cause electric shock or a fire.

DB68-06570B-00

N(1) 1

✴✴

09/12✴✴TC

✴✴

10/13/18/24✴✴UN

✴✴

09/12/18/24✴✴ME

✴✴

09/12/18/24✴✴SS

✴✴

18/24✴✴TC

Fasten the screws for the wire holders.

Model

✴✴

09/12✴✴ME/TC

✴✴

10/13✴✴UN

✴✴

18✴✴ME/UN

✴✴

24✴✴ME/UN

Power cable

(Indoor unit)

3G X 1.0 mm²,

H05VV-F

3G X 1.5 mm²,

H05VV-F

3G X 2.5 mm²,

H05VV-F

Indoor-to-

Outdoor power

cable

4G X 1.5 mm²,

H07RN-F

4G X 1.5 mm²,

H07RN-F

3G X 1.0 mm²,

H07RN-F

1 X 0.75 mm²,

H05RN-F

Type GL

20 A

25A

Model

✴✴

09/12✴✴SS

✴✴

18/24✴✴SS/TC

Power cable

(Outdoor unit)

3G X 2.5 mm², H07RN-F

Outdoor-to-

Indoor power

cable

3G X 1.0 mm², H07RN-F

Communication

cable

2 X 0.75 mm², H05RN-F

Type GL

20 A

25 A

IM_TC_INV.indd 1

12/22/2016 12:57:52 PM