ASUS pi-xp6np5 사용자 설명서
ASUS P/I-XP6NP5 User's Manual
36
IV. BIOS SOFTWARE
IV
. BIOS
(BIOS Features)
Typematic Rate Setting (Disabled)
When enabled, you can set the two typematic controls listed next. Setup default
setting is Disabled.
When enabled, you can set the two typematic controls listed next. Setup default
setting is Disabled.
Typematic Rate (Chars/Sec)
This field controls the speed at which the system registers repeated keystrokes.
Options range from 6 to 30 characters per second. Setup default setting is 6; other
settings are 8, 10, 12, 15, 20, 24, and 30.
This field controls the speed at which the system registers repeated keystrokes.
Options range from 6 to 30 characters per second. Setup default setting is 6; other
settings are 8, 10, 12, 15, 20, 24, and 30.
Typematic Delay (Msec) (250ms)
This field sets the time interval for displaying the first and second characters. Four
delay rate options are available: 250ms, 500ms, 750ms and 1000ms.
This field sets the time interval for displaying the first and second characters. Four
delay rate options are available: 250ms, 500ms, 750ms and 1000ms.
OS/2 Onboard Memory > 64M (Disabled)
When using OS/2 operating systems with installed DRAM of greater than 64MB,
you need to Enable this option otherwise leave this on the setup default of Disabled.
......................................................................................................................................
When using OS/2 operating systems with installed DRAM of greater than 64MB,
you need to Enable this option otherwise leave this on the setup default of Disabled.
......................................................................................................................................
Security Option (System)
This field determines when the system prompts for the password. The default set-
ting is System, where the system prompts for the User Password every time you boot
up. The other option is Setup, where the system always boots up, and prompts for
the Supervisor Password only when the Setup utility is called up. You can specify a
password by using the Supervisor Password or User Password option from the main
screen as explained later in this section.
This field determines when the system prompts for the password. The default set-
ting is System, where the system prompts for the User Password every time you boot
up. The other option is Setup, where the system always boots up, and prompts for
the Supervisor Password only when the Setup utility is called up. You can specify a
password by using the Supervisor Password or User Password option from the main
screen as explained later in this section.
PCI/VGA Palette Snoop (Disabled)
Some display cards that are nonstandard VGA such as graphics accelerators or MPEG
Video Cards may not show colors properly. The setting Enabled should correct this
problem. Otherwise leave this on the setup default setting of Disabled.
Some display cards that are nonstandard VGA such as graphics accelerators or MPEG
Video Cards may not show colors properly. The setting Enabled should correct this
problem. Otherwise leave this on the setup default setting of Disabled.
Video BIOS Shadow (Enabled)
This field allows you to change the video BIOS location from ROM to RAM. Relo-
cating to RAM enhances system performance, as information access is faster than
the ROM.
This field allows you to change the video BIOS location from ROM to RAM. Relo-
cating to RAM enhances system performance, as information access is faster than
the ROM.
C8000-CBFFF to DC000-DFFFF (Disabled)
These fields are used for shadowing other expansion card ROMs. If you install
other expansion cards with ROMs on them, you will need to know which addresses
the ROMs use to shadow them specifically. Shadowing a ROM reduces the memory
available between 640KB and 1024KB by the amount used for this purpose.
These fields are used for shadowing other expansion card ROMs. If you install
other expansion cards with ROMs on them, you will need to know which addresses
the ROMs use to shadow them specifically. Shadowing a ROM reduces the memory
available between 640KB and 1024KB by the amount used for this purpose.
PS/2 Mouse Control (Auto)
The default of Auto allows the system to detect a PS/2 Mouse on bootup. If de-
tected, IRQ12 will be used for the PS/2 Mouse. IRQ12 will be reserved for expan-
sion cards if a PS/2 Mouse is not detected. Disabled will reserve IRQ12 for expan-
sion cards and therefore the PS/2 Mouse will not function.
The default of Auto allows the system to detect a PS/2 Mouse on bootup. If de-
tected, IRQ12 will be used for the PS/2 Mouse. IRQ12 will be reserved for expan-
sion cards if a PS/2 Mouse is not detected. Disabled will reserve IRQ12 for expan-
sion cards and therefore the PS/2 Mouse will not function.