Sony CFD-F10L 사용자 설명서

Press RADIO BAND•AUTO PRESET until the band you want appears in the
display (direct power-on).
Each time you press the button, the indication changes as follows:
CFD-F10: “FM” 

t “AM”

CFD-F10L: “FM” 

t “MW” t “LW”

Hold down TUNE + or – until the frequency digits begin to change in the
display.

The player automatically scans the radio frequencies and stops when it finds a
clear station.
If you can't tune in a station, press the button repeatedly to change the frequency
step by step.

If the FM broadcast is noisy, press MODE repeatedly until “Mono” appears in the display and the radio
will play in monaural.

The AM/MW tuning interval is preset to 9 kHz at the factory.

If you need to change the AM/MW tuning interval, do the following:

1 While keeping the RADIO BAND•AUTO PRESET button and TAPE button pressed,

disconnect the mains lead from the mains.

2 While keeping the RADIO BAND•AUTO PRESET button and TAPE button pressed,

reconnect the mains lead to the mains. The tuning interval is changed and “AM 9”
“MW 9” or “AM 10” “MW 10” appears in the display for 2 seconds.

After changing the tuning interval, you need to reset your preset radio stations.

You can store radio stations into the player’s memory. You can preset up to 30 radio stations
(CFD-F10), 20 for FM and 10 for AM in any order, or 40 radio stations (CFD-F10L), 20 for FM,
10 for MW and 10 for LW in any order.

Press RADIO BAND•AUTO PRESET to select the band.

Hold down RADIO BAND•AUTO PRESET for 2 seconds until “AUTO” flashes
in the display.

Press DSPL/ENT/MEM.
The stations are stored in memory from the lower frequencies to the higher ones.

You need to preset a station with a weak signal manually.

1 Press RADIO BAND•AUTO PRESET to select the band.

2 Tune in a station you want.

3 Hold down DSPL/ENT/MEM for 2 seconds until the preset number flashes in the display.

4 Press PRESET + or – until the preset number you want for the station flashes in the display.

5 Press DSPL/ENT/MEM.

The new station replaces the old one.

1 Press BAND until the band you want appears in the display.

2 Tune in a station you want.

3 Hold down the number buttons that you want to preset the new station on for about 2 seconds.

To select the preset number over 10, press >10 first, then the corresponding number buttons.
You need to hold down the last number button to enter for about 2 seconds.
(Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.)

The preset radio stations remain in memory even if you unplug the mains lead or remove the batteries.

Press RADIO BAND•AUTO PRESET to select the band.

Press PRESET + or – to tune in the stored station.

1 Press BAND.

2 Press the number buttons to tune in the stored station.

To tune in a preset station over 10, press >10 first, then corresponding number buttons.
(Example: To tune in a preset station 12, press >10 and 1 first, and then press 2.)

CFD-F10L: Press OPERATE.

CFD-F10: Press POWER.

Press VOLUME +, – (VOL +, –  on the remote).

Connect the headphones to the i (headphones) jack.

Press MEGA BASS.

“MEGA BASS” appears in the display.

To return to normal sound, press the button again.

Press MEGA Xpand.

“MEGA Xpand” appears in the display.

You can get the effect of expansion of the sound field.

To return to normal sound, press the button again.

1 Play the music source you want.
2 Press SLEEP to display “SLEEP.”
3 Press SLEEP to select the minutes until the player goes off automatically.

Each time you press the button, the indication changes as follows:   “60” 

t “90” t “120”

t “OFF” t “10” t “20” t “30”

Press OPERATE (or POWER) to turn off the power.

When you are playing a tape using this function:
If the tape length of one side is longer than the set time, the player will not go off until the tape reaches
the end.

N

x

.

>

Press CD (direct power-on).
(On the remote, press OPERATE (or POWER) and then press FUNCTION
repeatedly until “Cd” appears in the display.)

Load a CD in the CD compartment.

Press Z PUSH OPEN/CLOSE to close the CD compartment.

Press u (N

N

N

N

N on the remote).

The player plays all the tracks once.

stop playback

pause playback

go to the next track

go back to the previous track

remove the CD

locate a point while listening
to the sound

locate a point while observing
the display

locate a specific track directly*

* You cannot locate a specific track if “SHUF” or “PGM” is lit in the display. Turn off the indication by

pressing x.

To locate a track numbered over 10, press >10 first, then the corresponding number buttons on the
remote.
Example:To play track number 23, press >10 first, then 2 and 3.

Press DSPL/ENT/MEM in stop mode (see fig. D).

Press DSPL/ENT/MEM repeatedly while playing a CD. The display changes as follows:

t the current track number and playing time

r
the current track number and the remaining time on the current track*

r
the number of tracks left and remaining time on the CD

* For a track whose number is more than 20, the remaining time appears as “- -:- -” in the display.

Press MODE until “REP 1” “REP ALL” “SHUF” “SHUF REP” “PGM” “PGM REP” appears in
the display.  Then proceed as follows:

repeat a single track

“REP 1”

repeat all tracks

“REP ALL”

shuffle play

“SHUF”

repeat tracks

“SHUF REP”

in random order

programme play

“PGM”

repeat programmed tracks

“PGM REP”

When you’ve selected “PGM” or “PGM REP”, press the number buttons for the track you want
up to 20 tracks, then press N.

Press MODE repeatedly until the selected mode disappears from the display.

To check the order of tracks before play, press DSPL/ENT/MEM.

Every time you press the button, the track number appears in the programmed order.

Press x once if the CD is stopped and twice if the CD is playing. The current programme will be
erased. Then create a new programme following the programming procedure.

• You can play the same programme again, since the programme is saved until you open the CD

compartment.

• You can record your own programme. After you’ve created the programme, insert a blank tape and

press z to start recording.

Press . or > to select the track that you
want to repeat, then press u.

Press u.

Press u.

Press u.

Press . or > then press DSPL/ENT/MEM
for the tracks you want to programme in the order
you want up to 20 tracks (see fig. E). Then press
u.

Press . or > then press DSPL/ENT/MEM
for the tracks you want to programme in the order
you want up to 20 tracks. Then Press u.

D

E

x

u (X

X

X

X

X on the remote)

Press the button again to resume play after pause.

>

.

Z PUSH OPEN/CLOSE

M (forward) or m (backward) while playing until you
find the point (> or . on the remote)

M (forward) or m (backward) in pause until you find
the point (> or . on the remote)

a number button of the track on the remote

x

X

i

m

M

u

.

>

Z

You can record a CD on a MiniDisc and enjoy the sound from other components, such as
portable MD, CD player and TV, VCR through the speakers of this player.

Be sure to turn off the power of each component before making connections. For details, refer to
the instructions of the component to be connected.

Connect the OPTICAL DIGITAL OUT (CD) jack of this player with the digital
input jack of MiniDisc and DAT using the digital connecting cable* (not
supplied).

* Select a connecting cable depending on the type of the digital input jack of the recorder to be

connected. For details, refer to the instruction manual of the component to be connected. The
OPTICAL DIGITAL OUT (CD)  jack of this player is square-shaped jack.

Optical miniplug

POC-15AB

(MiniDisc recorder, etc.)

Square-shaped optical

POC-15A

connector (MiniDisc
recorder, DAT recorder, etc.)

Turn on the power of this player and the connected component.

Make the connected component ready for recording.

Press u to start playing a CD.

Connect the LINE IN jack of this player with the line output jack or headphones
jack of other component using the audio connecting cable* (not supplied).

* For MiniDisc recorder: a cable with a stereo-mini plug on both ends.
* For TV, VCR: a cable with a stereo-mini plug on one end and two phono plugs

on the other end.

Press LINE to display “LInE”.

Play the optional component connected to the LINE IN jack of the player.

You can record the sound from the connected component. Insert a blank tape into the tape compartment,
and press z.

Connect the cords firmly to avoid any malfunction.

Press TAPE (direct power-on).
(On the remote, press OPERATE (or POWER) and then press FUNCTION
repeatedly until “TAPE” appears in the display.)

Press xZ to open the tape compartment and insert a recorded tape. Close the
compartment. Use TYPE I (normal) tape only.

Press N.

stop playback

xZ

fast-forward or rewind the tape

M or m

pause playback

X

Press the button again to resume play after pause.

eject the cassette

xZ

Press xZ to open the tape compartment and insert a blank tape. Use TYPE I
(normal) tape only.

Select the programme source you want to record.

Press CD and insert a CD (See “Playing a CD”).

Press RADIO BAND•AUTO PRESET and tune in the station you want (See
“Listening to the radio”).

Press z to start recording.
(N is depressed automatically.)

stop recording

xZ

pause recording

X

Press the button again to resume recording.

• Adjusting the volume or the audio emphasis will not affect the recording level.
• CFD-F10L only: If the AM or MW/LW programme makes a whistling sound after you've pressed z

in step 3, press MODE to select the position of ISS (Interference Suppress Switch) that most decreases
the noise.

• For the best results, use the AC power as a power source for recording.
• To erase a recording, proceed as follows:

1 Insert a tape with the recording you want to erase.
2 Press TAPE.
3 Press z.