Sony DTC-ZE700 사용자 설명서
20
EN
Additional Information
Troubleshooting
If you’ve experienced any of the following difficulties
while using the deck, use this section as a guide to
remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
while using the deck, use this section as a guide to
remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
The cassette holder does not close.
/ Check that the cassette is inserted correctly (see pages 6
and 8).
/ Insert the cassette beyond the silver bar (see pages 6 and
8).
The function buttons do not work.
/ The deck has just been turned on and will not operate for
about 4 seconds. Wait 4 seconds (10 seconds when
“CLEANING” appears) before attempting any operation.
“CLEANING” appears) before attempting any operation.
/ The P button is activated. Press P to cancel pause.
/ The tape has reached its end. Press 0 to rewind the
/ The tape has reached its end. Press 0 to rewind the
tape.
No sound.
/ Make the proper connections (see pages 4 and 5).
/ The connected amplifier is not being operated properly.
/ The connected amplifier is not being operated properly.
Operate the amplifier as required for the respective deck
operation. (Refer to the operating instructions of the
amplifier.)
operation. (Refer to the operating instructions of the
amplifier.)
The deck does not record.
/ The record-protect hole on the cassette is open. Slide the
record-protect tab to close the hole (see page 7).
/ The INPUT switch is incorrectly set. Set INPUT to the
correct position.
/ The REC LEVEL control is set at 0. Turn REC LEVEL
clockwise to raise the recording level (only during
analog recording).
analog recording).
/ The signal input to the digital input jack or connector is
protected against digital copying (only during digital
recording). Input the signal through the analog input
jack or connector.
recording). Input the signal through the analog input
jack or connector.
The OPEN/CLOSE
§ button does not work.
/ The OPEN/CLOSE § button does not function during
recording. Press
p or P to stop recording first, then
press OPEN/CLOSE
§.
“CAUTION” appears and the deck cannot be operated.
/ A safety mechanism is operating because of
condensation. Remove the cassette and leave the deck
turned on for about an hour. Then turn the deck off,
then on again (see page 18).
turned on for about an hour. Then turn the deck off,
then on again (see page 18).
Sub codes writing is not possible.
/ The record-protect hole on the cassette is open. Slide the
record-protect tab to close the hole (see page 7).
Start ID writing is not possible during recording.
/ The start ID cannot be written within 9 seconds (18
seconds in long-play mode) after the end of the previous
start ID. Make sure at least 9 seconds (18 seconds in the
long-play mode) has passed after the last start ID and
before writing a new one.
start ID. Make sure at least 9 seconds (18 seconds in the
long-play mode) has passed after the last start ID and
before writing a new one.
Direct Access does not work.
/ The specified program number does not exist on the
tape. Press START ID RENUMBER to renumber the
program numbers.
program numbers.
/ The program numbers are out of order. Press START ID
RENUMBER to renumber the program numbers.
The deck begins rewinding the tape during playback.
/ Repeat Play is on. Press REPEAT on the remote
repeatedly to turn off “REPEAT” or “REPEAT 1” in the
display and cancel Repeat Play.
display and cancel Repeat Play.
The tape operation buttons do not function while writing
or erasing a start ID.
or erasing a start ID.
/ All buttons do not work during the 9 seconds the start ID
is being written (18 seconds in long-play mode). Wait
until the writing the start ID finishes before operation.
until the writing the start ID finishes before operation.
Absolute time codes writing is not possible.
/ Recording began within a blank section.
Rewind the tape to its beginning, or locate the end of the
recorded portion with End Search before starting
recording.
recorded portion with End Search before starting
recording.
Tape transport is excessively loud during fast-forwarding
or rewinding.
or rewinding.
/ The noise is caused by the cassette and is not a
mechanical problem.
The tape stops suddenly.
/ The cassette is defective or damaged.
Press OPEN/CLOSE
§ and replace the cassette with a
new one.
When pressing
0 /) or ≠/±, the tape stops
momentarily before starting to move.
/ This is normal and is not a mechanical problem.
The deck cannot be operated with the remote (supplied).
/ The battery is weak. Change both batteries.
“SBM” does not appear in the display even though SBM
is set to ON.
is set to ON.
/ ”SBM” appears only during the recording of analog
input signals with a sampling frequency of 48 kHz or
44.1 kHz, not during the recording of a digital input
signal, or an analog input signal with a sampling
frequency of 32 kHz, or during playback.
44.1 kHz, not during the recording of a digital input
signal, or an analog input signal with a sampling
frequency of 32 kHz, or during playback.