Sony dvp-cx777es 사용자 설명서
90
◆ BLACK LEVEL (COMPONENT OUT)
Selects the black level (setup level) for the
video (NTSC) signals output from the
COMPONENT VIDEO OUT jacks. You
cannot select this when “PROGRESSIVE” is
selected in “COMPONENT OUT” (see
below).
Selects the black level (setup level) for the
video (NTSC) signals output from the
COMPONENT VIDEO OUT jacks. You
cannot select this when “PROGRESSIVE” is
selected in “COMPONENT OUT” (see
below).
◆ COMPONENT OUT
Selects the type of signal output from the
COMPONENT VIDEO OUT jacks when the
COMPONENT VIDEO OUT/SCAN
SELECT switch on the rear panel of the
player is set to SELECTABLE. See page 101
for more information about the two different
signal types.
COMPONENT VIDEO OUT jacks when the
COMPONENT VIDEO OUT/SCAN
SELECT switch on the rear panel of the
player is set to SELECTABLE. See page 101
for more information about the two different
signal types.
About the COMPONENT VIDEO OUT/SCAN
SELECT switch
SELECT switch
The COMPONENT VIDEO OUT/SCAN
SELECT switch on the rear panel of the
player selects the signal output from the
COMPONENT VIDEO OUT jacks:
interlace, progressive, or selectable. The
switch takes priority over the setting made in
“COMPONENT OUT.”
SELECT switch on the rear panel of the
player selects the signal output from the
COMPONENT VIDEO OUT jacks:
interlace, progressive, or selectable. The
switch takes priority over the setting made in
“COMPONENT OUT.”
To switch the video signal format
If you have selected “PROGRESSIVE” for a
TV that does not accept signals in progressive
format 480p, or if the software’s video signals
are not suited for progressive video signal
conversion, view the image in Interlace
format.
TV that does not accept signals in progressive
format 480p, or if the software’s video signals
are not suited for progressive video signal
conversion, view the image in Interlace
format.
1
Set the COMPONENT VIDEO OUT/
SCAN SELECT switch on the rear panel
of the player to INTERLACE.
“COMPONENT OUT” in “SCREEN
SETUP” is automatically set to
“INTERLACE.”
SCAN SELECT switch on the rear panel
of the player to INTERLACE.
“COMPONENT OUT” in “SCREEN
SETUP” is automatically set to
“INTERLACE.”
2
Reset the COMPONENT VIDEO OUT/
SCAN SELECT switch to
SELECTABLE.
Normally leave the switch in this position
when using the COMPONENT VIDEO
OUT jacks.
SCAN SELECT switch to
SELECTABLE.
Normally leave the switch in this position
when using the COMPONENT VIDEO
OUT jacks.
When “PROGRESSIVE” is selected in
“COMPONENT OUT”
“COMPONENT OUT”
• 4:3 OUTPUT
Adjust this when you watch progressive
signals on a standard 4:3 aspect ratio
television. If you can change the aspect ratio
on your progressive format (480p)
compatible TV, change the setting on your
TV, not the player.
Adjust this when you watch progressive
signals on a standard 4:3 aspect ratio
television. If you can change the aspect ratio
on your progressive format (480p)
compatible TV, change the setting on your
TV, not the player.
ON
Sets the black level of the
output signal to the standard
level.
output signal to the standard
level.
OFF
Lowers the standard black
level. Use this when the picture
becomes too white.
level. Use this when the picture
becomes too white.
INTERLACE
Select this when the
player is connected to a
standard (interlace
format) TV.
player is connected to a
standard (interlace
format) TV.
PROGRESSIVE
Select this when you have
a TV that can accept
progressive signals.
a TV that can accept
progressive signals.
FULL
Select this when you can change
the aspect ratio on your TV.
the aspect ratio on your TV.
NORMAL
Select this when you cannot
change the aspect ratio on your
TV. Shows a 16:9 aspect ratio
signal with black bands on left
and right sides of the image, and
a 4:3 aspect ratio signal with
black bands on all sides of the
image.
change the aspect ratio on your
TV. Shows a 16:9 aspect ratio
signal with black bands on left
and right sides of the image, and
a 4:3 aspect ratio signal with
black bands on all sides of the
image.
16:9 aspect ratio TV
4:3 aspect ratio TV