Sony dvp-ns900v 사용자 설명서
So
und Adj
und Adj
u
s
tme
nt
s
nt
s
65
VIRTUAL MULTI DIMENSION
Uses sound imaging to create an array of virtual
rear speaker positions higher than the listener
from a single pair of actual rear speakers.
This mode creates five sets of virtual
speakers surrounding the listener at
approximately a 30
rear speaker positions higher than the listener
from a single pair of actual rear speakers.
This mode creates five sets of virtual
speakers surrounding the listener at
approximately a 30
°
angle of elevation. The
effect differs according to “REAR” or
“SIDE” setting of the rear speakers (page 94).
“SIDE” setting of the rear speakers (page 94).
z
You can use the LCD and scroll key on the remote
to select a surround setting. Toggle the scroll key up or
down so that “SURROUND” appears in the LCD
screen. Then press down on the scroll key repeatedly
to select one of the surround sounds.
down so that “SURROUND” appears in the LCD
screen. Then press down on the scroll key repeatedly
to select one of the surround sounds.
Notes
•
To enjoy the multichannel audio through the 5.1CH
OUTPUT jacks, correctly set each speaker position
and distance. For details on setting each speaker, see
page 94.
OUTPUT jacks, correctly set each speaker position
and distance. For details on setting each speaker, see
page 94.
•
When you select an item, the sound cuts off for a
moment.
moment.
•
When the playing signal does not contain a signal for
the rear speakers (page 61), the surround effects may
be difficult to hear.
the rear speakers (page 61), the surround effects may
be difficult to hear.
•
When you select “TVS DYNAMIC,” “TVS WIDE,”
“TVS NIGHT”, or “TVS STANDARD,” the player
does not output the sound from the centre speaker.
“TVS NIGHT”, or “TVS STANDARD,” the player
does not output the sound from the centre speaker.
•
When you select one of the surround modes, turn off
the surround setting of the connected TV or
amplifier (receiver).
the surround setting of the connected TV or
amplifier (receiver).
•
If the player is set up to output the signal from the
DIGITAL OUT (OPTICAL or COAXIAL) jack, the
TVS effect will not be heard when you play a CD.
DIGITAL OUT (OPTICAL or COAXIAL) jack, the
TVS effect will not be heard when you play a CD.
•
Make sure that your listening position is between
and at an equal distance from your speakers, and that
the speakers are located in similar surroundings.
Otherwise, the TVS effect may be hard to discern.
and at an equal distance from your speakers, and that
the speakers are located in similar surroundings.
Otherwise, the TVS effect may be hard to discern.
•
“TVS NIGHT” only works with Dolby Digital discs.
However, not all discs will respond to the “TVS
NIGHT” function in the same way.
However, not all discs will respond to the “TVS
NIGHT” function in the same way.
•
If you use the DIGITAL OUT (OPTICAL or
COAXIAL) jack and set “DOLBY DIGITAL” to
“DOLBY DIGITAL,” “DTS” to “DTS,” and
“MPEG” to “MPEG” in “AUDIO SETUP,” sound
will come from your speakers but it will not have the
TVS effect.
COAXIAL) jack and set “DOLBY DIGITAL” to
“DOLBY DIGITAL,” “DTS” to “DTS,” and
“MPEG” to “MPEG” in “AUDIO SETUP,” sound
will come from your speakers but it will not have the
TVS effect.
L : Front speaker (left)
R : Front speaker (right)
LS :Rear speaker (left)
RS :Rear speaker (right)
R : Front speaker (right)
LS :Rear speaker (left)
RS :Rear speaker (right)
: Virtual speaker
L
LS
RS
R
L
R
LS
RS
SIDE
REAR
LS
RS
L
R
L
R
LS
RS
SIDE
REAR