Sony HCD-LX10000 사용자 설명서
34
US
Cleaning the cabinet
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with mild detergent solution. Do not
use any type of abrasive pad, scouring powder or
solvent such as thinner, benzene or alcohol.
slightly moistened with mild detergent solution. Do not
use any type of abrasive pad, scouring powder or
solvent such as thinner, benzene or alcohol.
To save a tape permanently
To prevent a tape from being accidentally recorded
over, break off the tape tab from side A or B as
illustrated.
over, break off the tape tab from side A or B as
illustrated.
If you later want to reuse the tape for recording, cover
the broken tab with adhesive tape.
the broken tab with adhesive tape.
Before placing a tape in the tape deck
Take up any slack in the tape deck. Otherwise, the tape
may get entangled in the parts of the tape deck and
become damaged.
may get entangled in the parts of the tape deck and
become damaged.
When using a tape longer than
90 minutes
90 minutes
The tape is very elastic. Do not change the tape
operations such as playback, stop and fast-winding etc.
frequently. The tape may get entangled in the tape
deck.
operations such as playback, stop and fast-winding etc.
frequently. The tape may get entangled in the tape
deck.
Cleaning the tape heads
Clean the tape heads after every 10 hours of use. Be
sure to clean the tape heads before you start an
important recording or after playing an old tape. Use a
separately sold dry-type or wet-type cleaning tape. For
details, refer to the instructions of the cleaning tape.
sure to clean the tape heads before you start an
important recording or after playing an old tape. Use a
separately sold dry-type or wet-type cleaning tape. For
details, refer to the instructions of the cleaning tape.
Demagnetizing the tape heads
Demagnetize the tape heads and the metal parts that
have contact with the tape after every 20 to 30 hours of
use with a separately sold demagnetizing tape. For
details, refer to the instructions of the demagnetizing
tape.
have contact with the tape after every 20 to 30 hours of
use with a separately sold demagnetizing tape. For
details, refer to the instructions of the demagnetizing
tape.
AUDIO POWER SPECIFICATION
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
DISTORTION:
With 6-ohm loads, per channel driven, from
120 Hz – 10 kHz; rates 230 watts per channel
minimum RMS power, with no more than 10% total
harmonic distortion from 250 milliwatts to rated
output.
120 Hz – 10 kHz; rates 230 watts per channel
minimum RMS power, with no more than 10% total
harmonic distortion from 250 milliwatts to rated
output.
Amplifier section
Total harmonic distortion
Less than 0.1%
(6 ohms at 1 kHz, 100 W)
(6 ohms at 1 kHz, 100 W)
Inputs
VIDEO/MD (AUDIO) IN (phono jacks):
VIDEO/MD (AUDIO) IN (phono jacks):
voltage 250/450 mV,
impedance 47 kiloohms
impedance 47 kiloohms
TV (AUDIO) IN (phono jack):
voltage 250 mV,
impedance 47 kiloohms
impedance 47 kiloohms
MIC (phone jack):
sensitivity 1 mV,
impedance 10 kiloohms
impedance 10 kiloohms
Outputs
PHONES (stereo mini jack):
PHONES (stereo mini jack):
accepts headphones of
8 ohms or more
8 ohms or more
FRONT SPEAKER:
Use only the supplied
speaker
speaker
SURROUND SPEAKER: Use only the supplied
speaker
Disc player section
System
Compact disc and digital
audio system
audio system
Laser
Semiconductor laser
(
(
λ=780 nm)
Emission duration:
continuous
continuous
Laser Output
Max. 44.6
µW*
*This output is the value
measured at a distance of
200 mm from the objective
lens surface on the Optical
Pick-up Block with 7 mm
aperture.
measured at a distance of
200 mm from the objective
lens surface on the Optical
Pick-up Block with 7 mm
aperture.
Frequency response
2 Hz – 20 kHz (±0.5 dB)
Wave length
780 – 790 nm
Signal-to-noise ratio
More than 90 dB
Dynamic range
More than 90 dB
Break off the
tape tab
tape tab
Specifications