Sony SVT-S480ES 사용자 설명서
57
Data format
RS-232C
Mode
Asynchronous
Character length
8 bits
Baud rate
2400, 4800, 9600 or 19200
Parity check
None
Stop bit
1 bit
The baud rate can also be set using the VCR menu.
See page 56 for details.
See page 56 for details.
Communication protocol
The communication is based on 1 byte unit. When the
computer has transmitted 1 byte, it will wait for a
response from the VCR, then send the next.
The response from the VCR consists of 1 byte or more
(for example 6 bytes like the counter value).
computer has transmitted 1 byte, it will wait for a
response from the VCR, then send the next.
The response from the VCR consists of 1 byte or more
(for example 6 bytes like the counter value).
RS-485
Mode
Asynchronous
Character length
8 bits
Baud rate
2400, 4800, 9600 or 19200
Parity check
None
Start bit
1 bit
Stop bit
1 bit
Transmission line: 2 conductors
Transmission system: Half duplex
Transmission system: Half duplex
Note
The commands depend on the VCR which you are going to
use. Even if you send the commands which are not provided
with your VCR, they do not function.
use. Even if you send the commands which are not provided
with your VCR, they do not function.
The received/transmitted (RXD/TXD) signal layout is
indicated as seen from the VCR side.
indicated as seen from the VCR side.
The baud rate can also be set using the VCR menu.
See page 56 for details.
See page 56 for details.
Note on using the RS-232C
To initiate command operation, send TL TABLE ON
(F6H).
The VCR will responde with ACK (0AH).
The VCR will receive commands until you send TL
TABLE OFF (F7H) to end command operations.
(F6H).
The VCR will responde with ACK (0AH).
The VCR will receive commands until you send TL
TABLE OFF (F7H) to end command operations.
Note on using the RS-485
If the address set using the DIP switches is not correct,
the VCR will not operate.
When a group number is set, if it does not match the
group number of the VCR, the VCR will not operate.
the VCR will not operate.
When a group number is set, if it does not match the
group number of the VCR, the VCR will not operate.
VCR Control Commands
The following commands are completed in 1 byte.
The VCR will respond with ACK (0AH). Confirm that
ACK (0AH) is returned before sending the next
command.
The VCR will respond with ACK (0AH). Confirm that
ACK (0AH) is returned before sending the next
command.
POWER ON/OFF (7BH)
Turns on or off the VCR.
PLAY (3AH)
Plays back a tape.
STILL/PAUSE (4FH)
Pauses tape.
When this command is sent while recording, the VCR
enters recording pause mode
When this command is sent while recording, the VCR
enters recording pause mode
STOP (3FH)
Stops tape.
FF (ABH)
Fast forwards the tape.
When this command is sent while playing, the VCR
enters playback in fast-forward mode.
During pause, the VCR plays back still picture.
During alarm search/scan or date/time search, the VCR
switches to forward search/scan.
When this command is sent while playing, the VCR
enters playback in fast-forward mode.
During pause, the VCR plays back still picture.
During alarm search/scan or date/time search, the VCR
switches to forward search/scan.
REW (ACH)
Rewinds the tape.
When this command is sent while playing, the VCR
enters playback in reverse.
During pause, the VCR plays back still picture in
reverse.
During alarm search/scan or date/time search, the VCR
switches to reverse search/scan.
When this command is sent while playing, the VCR
enters playback in reverse.
During pause, the VCR plays back still picture in
reverse.
During alarm search/scan or date/time search, the VCR
switches to reverse search/scan.
REV PLAY (4AH)
Plays back a tape in reverse at normal speed.
RP SPEED MODE DATA SET (7FH)
Sets recording mode to SP or EP.
TIMER ON/OFF (60H)
Switches on/off timer recording.
SECURITY LOCK ON (69H)
Switches on security lock.
SECURITY LOCK OFF (6AH)
Switches off security lock.
Command Reference