Sony xdr-cd70dab 사용자 설명서

XDR-CD70DAB 3-214-191-11(1)

XDR-CD70DAB 3-214-191-11(1)

 Press VOLUME + or – repeatedly to adjust

the volume.

Pause

CD 

Resume play after pause

CD  again

Cue to the beginning of the

current track (AMS*)

**

Cue to the next track (AMS*)

**

Go back at high speed

Hold down **

Go forward at high speed

Hold down **

Locate a previous track (AMS*)  repeatedly**
Locate a succeeding track

(AMS*)

 repeatedly**

Stop play



*  AMS = Automatic Music Sensor

**  These operations are possible during both play and

pause.

 During CD playback, every time you press

DISPLAY, the track number appears in the display

for a few seconds.

This unit is compatible with CD-Rs/CD-RWs but

playback capability may vary depending on the quality

of the disc, the recording device and application

software.

This product is designed to play back discs that

conform to the Compact Disc (CD) standard.

Recently, various music discs encoded with copyright

protection technologies are marketed by some

record companies. Please be aware that among those

discs, there are some that do not conform to the CD

standard and may not be playable by this product.
To handle compact discs

Do not touch the surface.

Correct

Handle the disc by its edge.

Incorrect

Do not stick paper or

tape on the surface.

A DualDisc is a two sided disc product which mates

DVD recorded material on one side with digital

audio material on the other side. However, since the

audio material side does not conform to the Compact

Disc (CD) standard, playback on this product is not

guaranteed.
Notes

 Discs with non-standard shapes (e.g., heart, square,

star) cannot be played on this unit. Attempting to do

so may damage the unit. Do not use such discs.

 If you press CD  when there is no disc in the CD

compartment, “00” flashes for about 5 seconds in

the display and the unit turns off automatically.

You can play tracks repeatedly or in random order.

Press MODE.

Each press changes the play mode as follows:

None

(normal play)

All the tracks are played once.



“REP 1”

(single repeat)

A single track is played repeatedly.



“REP”

(all repeat)

All the tracks are played repeatedly.



“SHUFFLE”

(shuffle play)

All the tracks are played once

in random order.



“SHUFFLE REP”

(shuffle repeat)

All the tracks are played repeatedly

in random order.

The unit can receive DAB services and FM stations,

for which the Preset and Manual tuning modes can

be used. For DAB services, Alphabetical mode is also

available.

There are the following three tuning modes:

Alphabetical mode (DAB only): For selecting stored

services listed in alphabetical order.

By pressing the SNOOZE/BRIGHTNESS button, you

can select the brightness level of the backlight and

illumination.

The brightness level of the backlight changes in

conjunction with that of the illumination.

Upper : Backlight level

Lower : Illumination level

While the alarm is sounding, the SNOOZE/

BRIGHTNESS button cannot be used to change the

brightness of the display. It can, however, be used for

the SNOOZE function.

An 8 cm (3-inch) CD can be played without an

adaptor.

 Push PUSH OPEN/CLOSE to open the

CD compartment lid and insert a disc.

 Push PUSH OPEN/CLOSE to close the

CD compartment lid.

Push

Labelled surface up

Close the lid

 Press CD .

“CD” and “TRACK 01” appear in the display

to indicate that track 1 of the CD is playing.

The CD  button has a 

Preset mode: For selecting a favorite stored service

or station (see “Presetting Your Favorite Service or

Station”).

Manual mode (FM only): For adjusting the frequency

manually.

 Press FM/DABRADIO ON to turn on the

radio.

 Press FM/DABRADIO ON repeatedly to

select the desired band.

Each press changes the band as follows:

The default setting of the tuning mode is

Alphabetical mode in DAB, and Manual mode

in FM.

If you want to change to Preset mode in both DAB

and FM, see “Tuning in to a Preset Service or

Station (Preset mode)”.

 Use TUNETIME SET + or – to tune into

the desired service or station.

Two short beeps sound when the lowest ensemble

of DAB or the minimum frequency of FM is

received during tuning.

 Adjust the volume using VOLUME + or –.

When you release TUNETIME SET + or – after

locating your desired service or station, the display

returns to the current time after about 10 seconds.
To check the ensemble label of a tuned-in service of

DAB or the frequency of a tuned-in station of FM,

press FM/DABRADIO ON and the ensemble label or

the frequency will appear for about 10 seconds.
To turn off the radio, press OFF ALARM RESET.

 Before receiving DAB broadcasts, one or more

Before receiving DAB broadcasts, one or more

ensembles should be stored in the list by the DAB

scan (See “Initial Setting for the DAB”).

 “NO ENS” appears when the ensemble for the

“NO ENS” appears when the ensemble for the

selected service cannot be received.

 If a selected service finishes broadcasting, sound

If a selected service finishes broadcasting, sound

stops and “NO SRV” appears. In this case, press

TUNETIME SET + or – to select another service.

If the selected primary component has a secondary

component, “SC” flashes in the display.

Press TUNETIME SET + or – to receive the desired

secondary component.

“SC” lights up while the secondary component is

being received.

Pressing TUNETIME SET + or – does the following:

When the selected secondary component is finished,

the unit returns automatically to the primary

component.

You can preset up to 3 services in DAB, and 3 FM

stations.

 Follow steps 1 to 3 in “Listening to the

Radio” and manually tune in the service or

station you wish to preset.

 Hold down the desired PRESET TUNING

button (1 to 3) until two short beeps sound.

Example 1: The following display appears when

you preset FM 87.50 MHz to PRESET TUNING 2

button for FM.



The display shows the frequency for about 10

seconds, and then returns to the current time.

Example 2: The following display appears when

you preset BETA_1 to PRESET TUNING 1 button

for DAB.



The display shows the ensemble label for about 10

seconds, and then returns to the current time.

To preset another service or station, repeat these steps.

To change the preset service or station, tune in the

desired service or station and hold down the desired

PRESET TUNING (1 to 3) until two short beeps sound.

The new service or station will replace the service or

station previously set to the PRESET TUNING button.

 Press FM/DABRADIO ON to turn on the

radio.

 Press FM/DABRADIO ON to select the

band.

 Press the desired PRESET TUNING button.

When pressing TUNETIME SET + or – buttons

during DAB reception, the tuning mode will

change to Alphabetical mode (For more detail, see

“Listening to the Radio” ).

 Adjust the volume using VOLUME + or –.

After about 4 seconds, the display returns to the

current time.

Holding down the desired PRESET TUNING button

for 2 seconds or more in step 3 will replace the service

or station previously set to the PRESET TUNING

button with the service or station you are tuned in to.

To change the display mode, press DISPLAY during

DAB reception. The selected display mode remains

even if you turn the unit off and on again, or change

the band.

A dynamic label can be up to 128 characters in length.

An ensemble label can be up to 16 characters in

length.

A component label and service label can be up to 8

characters in length.

Each time you press DISPLAY, the display changes as

follows*:
Component label









*  When holding down DISPLAY for 2 seconds or

more, the display changes as follows:

Press DISPLAY again.



•  If there is no service label, no message will be

displayed.

•  If there is no dynamic label, “NO TEXT” will appear.

 Connect the built-in audio cable with the

stereo-miniplug on the bottom of the unit

to the line output jack or headphones jack

on the optional component (e.g., portable

music player).

 Press AUDIO IN.

“AUDIO IN” appears in the display

 Play the optional component connected to

the unit’s built-in audio cable.

 Adjust the volume using VOLUME + or –.

To turn off the sound from the optional component,

press OFFALARM RESET, and then turn off the

optional component. 
Notes

 Connect the built-in audio cable firmly to prevent a

malfunction.

 Keep digital music players away from the speakers.

This CD clock radio is equipped with 4 alarm

modes—CD, DAB, FM and buzzer. Before setting the

alarm, make sure to set the clock (see “Initial Setting

for the Clock”).

 Hold down ALARM A or B until a short

beep sounds.

The hour flashes in display.

 Press TUNETIME SET + or – repeatedly

until the desired hour appears.

To set the hour rapidly, hold down TUNETIME 

SET + or –.

 Press ALARM A or B.

A short beep sound and the minute flashes.

 Repeat step 2 to set the minute and press

ALARM A or B.

A short beep sound and the alarm mode setting

is entered.

 Press TUNETIME SET + or – repeatedly

until the desired alarm mode flashes.

You can choose one mode among “CD”, “DAB”,

“FM” and “BUZZER”. Set the alarm mode as

follows:

– CD: see “ Setting the CD Alarm”.

– DAB or FM: see “ Setting the DAB/FM

Alarm”.

– BUZZER: see “ Setting the Buzzer Alarm”.

 Setting the CD Alarm 

For the CD alarm, the track you specified as the wake-

up track is played first.

(If the CD play mode is set to “SHUFFLE” or

“SHUFFLE REP”, all the tracks will be played in

random order.)

 Perform steps 1 to 5 in “To set the Alarm”.

 Press ALARM A or B to select “CD” alarm

mode.

A short beep sounds and “WAKE UP TRACK”

appears in the display.

 Press TUNETIME SET + or – to select the

desired wake-up track number.

 Press ALARM A or B.

A short beep sounds and “WAKE UP VOL”

appears in the display.

 Press TUNETIME SET + or – to adjust the

volume.

You can also adjust the volume using VOLUME 

+ or –.

 Press ALARM A or B.

Two short beeps sound and the setting is entered.

When “ALARM A” or “ALARM B” does not

appear with “CD” in the display, press ALARM A

or B again.

The CD will play at the set time.

If the CD alarm does not operate because a

disc error occurred, there is no disc, or the CD

compartment lid is open, the buzzer alarm will

operate instead.

 Setting the DAB/FM Alarm

For the DAB or FM alarm, the service or station you

specifiy as the wake-up station is played.

 Perform steps 1 to 5 in “To set the Alarm”.

 Press ALARM A or B to select “DAB” or

“FM” alarm mode.

After the preset number flashes, “WAKE UP

PRESET” or “WAKE UP -- ” appears in the

display.

 Press TUNETIME SET + or – to select the

desired wake-up service or station.

The service or station changes as follows:
When DAB is selected

“– –” is the last service or station received.

You can directly select the desired wake-up service

or station by pressing FM/DABRADIO ON or

the PRESET TUNING button while the “– –”

indication is not displayed.

 Press ALARM A or B.

A short beep sounds and “WAKE UP VOL”

appears in the display.

 Press TUNETIME SET + or – to adjust the

volume.

You can also adjust the volume using VOLUME 

+ or –.

 Press ALARM A or B.

Two short beeps sound and the setting is entered.

When “ALARM A” or “ALARM B” does not

appear with “DAB” or “FM” in the display, press

ALARM A or B again.

The radio will turn on at the set time.

If the DAB alarm does not operate (e.g., when the

unit is unable to receive DAB services), the buzzer

alarm will operate instead.

 Setting the Buzzer Alarm

 Perform steps 1 to 5 in “To set the Alarm”.

 Press ALARM A or B to select “BUZZER”

alarm mode.

Two short beeps sound and the setting is entered.

When “ALARM A” or “ALARM B” does not

appear with “BUZZER” in the display, press

ALARM A or B again.

The buzzer will sound at the set time.

The volume cannot be set for the buzzer alarm.

Press ALARM A or B to activate the alarm setting.

If “ALARM A” or “ALARM B” does not appear in the

display, the alarm setting is not activated. You can only

check the alarm setting when it is activated.

Example: The following display shows the current

time and the CD ALARM A for 7:00 am.

If you set the CD alarm and there is no disc in the

CD player, the buzzer alarm will sound instead at the

time set.
In case of the alarm, the beeping of the alarm becomes

louder after every few seconds in three progressive

stages.
Note

When Alarm A and B are set for the same time, Alarm

A takes precedence.

PUSH OPEN/CLOSE

VOLUME +/–

SNOOZE/BRIGHTNESS

 Plug in the unit.

 Hold down DATE until a short beep sounds.

The year starts to flash in the display.

 Press TUNE



TIME SET + or – repeatedly to

set the year.

 Press DATE.

 Repeat steps 3 and 4 to set the month and

the day, and then press DATE.

Two short beeps sound and the year, month, and

day are set.

 Hold down CLOCK until a short beep

sounds.

The hour starts to flash in the display.

 Press TUNE



TIME SET + or – repeatedly to

set the hour.

 Press CLOCK.

 Repeat steps 2 and 3 to set the minutes, and

then press CLOCK.

Two short beeps sound and the seconds start

incrementing from zero.

 The clock setting will be cancelled if you press OFF 



ALARM RESET while setting the clock.

 If you do not press a button for about 1 minute while

setting the clock, the clock setting will be cancelled.

Press Date once for the date, and within 2 seconds

press it again for the year.

The display shows the date or year for about 4 seconds

and then changes back to the current time.

Hold down OFF 



ALARM RESET  and

and DATE until

two short beeps sound.

“ ” is displayed, “ON” appear for a few seconds,

and then the time changes to daylight saving time

(summer time).

To deactivate the daylight saving time (summer time)
function, hold down OFF 



ALARM RESET  and

and

DATE until two short beeps sound again.

“OFF” appears for a few seconds, and then “ ”

disappears.

Press SNOOZEBRIGHTNESS once.

“10” appears in the display and the CD, DAB, FM,

or BUZZER alarm stops. Every time you press

SNOOZEBRIGHTNESS, the snooze time changes as

follows:

The display shows the snooze time for a few seconds,

and then returns to the current time. When you

press SNOOZEBRIGHTNESS after the current time

appears, the snooze time goes back to 10 minutes

again.
The maximum length of the snooze time is 60

minutes.

Press OFF ALARM RESET to turn off the alarm.

The alarm will sound again at the same time the next

day.

Press ALARM A or B to deactivate the alarm setting.
The CD, DAB, FM, or buzzer alarm turns off

automatically after 60 minutes.
Note on the alarm in the event of a power 

In the event of a power interruption, the alarm will

work until the battery is totally discharged. But

following functions are different:

 During a power interruption, the display indications,

backlight and illumination will not light up.

 If the alarm mode is set to CD, DAB, or FM, it will

change to BUZZER automatically.

 If a power interruption occurs while the alarm is

sounding, the alarm will stop.

 If OFF ALARM RESET is not pressed, the alarm

sounds for about 5 minutes.

 If “” appears in the display, the alarm will not

sound in the event of power interruption. Replace

the battery if “” appears.

 If a power interruption occurs while the buzzer

alarm is sounding, the SNOOZE/BRIGHTNESS

button will not operate.

The NAP timer sounds the buzzer after a preset

duration has elapsed.
Press NAP repeatedly until the desired duration is

displayed.

Every press changes the display as follows:

“

” appears and the NAP time is displayed for a

few seconds.

NAP timer starts counting down.

When the selected NAP duration has ended, buzzer

sounds, and “

” flashes in the display.

The buzzer turns off automatically after about 60

minutes.

Press NAP or OFF ALARM RESET to turn off the

buzzer.

Press NAP.

“

” goes off in the display.

The sleep timer allows you to fall asleep to the sound

of a CD, DAB, FM, or input from the AUDIO IN

function. It does this by automatically turning off the

CD, DAB, FM, or input from the AUDIO IN function

after a preset duration.
Press SLEEP during CD, DAB, FM, or optional

component play.

You can set the sleep timer to durations of 90, 60, 30,

or 15 minutes. Every press changes the duration as

follows:

“SLEEP” will appear in the display when the duration

is set.

The CD, DAB, FM, or the optional component will

play for the set duration, and then shut off.

Press OFF ALARM RESET.