JVC RX-D211S 사용자 설명서
34
On the front panel:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
canceled before you finish, start from step
2 again.
1
Select and play any source.
• Make sure you have selected the input mode (analog or
digital) correctly.
2
Press SURROUND.
MULTI JOG now works for selecting Surround/DSP modes.
3
Turn MULTI JOG to select the Surround/DSP
mode you want.
mode you want.
Ex.: When “DOLBY DIGITAL” is selected for Dolby Digital
multi-channel software:
*
1
“AUTO SURROUND” is the initial setting.
*
2
Available Surround modes vary depending on the speaker
settings and the incoming signals. For details, see page 33.
settings and the incoming signals. For details, see page 33.
*
3
If an incoming signal is a multi-channel (2 channel or more)
digital signal, “MONO FILM” is not available.
digital signal, “MONO FILM” is not available.
*
4
If “SURROUND SPK” is set to “
<
NO
>
,” “ALL CH STEREO”
is not available.
To cancel Surround/DSP modes
Turn MULTI JOG so that “SURROUND OFF” appears on the
display.
display.
When you select “AUTO SURROUND”
You can enjoy the Surround mode easily.
• For details about the Surround modes, see page 33.
• When “AUTO SURROUND” is activated, the AUTO SURR indicator
• For details about the Surround modes, see page 33.
• When “AUTO SURROUND” is activated, the AUTO SURR indicator
lights up on the display.
How does “AUTO SURROUND” work?
• If a multi-channel signal comes in, an appropriate Surround
• If a multi-channel signal comes in, an appropriate Surround
mode will be selected automatically.
• If a Dolby Digital 2-channel signal with surround signal
comes in, “PLIIx MOVIE” or “PLII MOVIE” will be selected.
• If a Dolby Digital 2-channel signal without surround signal
comes in, “SURROUND OFF (stereo)” will be selected.
• If a Linear PCM signal comes in, “SURROUND OFF (stereo)”
will be selected.
NOTE
“AUTO SURROUND” does not take effect in the following
cases:
cases:
– While playing an analog source,
– While selecting one of the fixed digital input mode—“DOLBY
– While selecting one of the fixed digital input mode—“DOLBY
DIGITAL” or “DTS” (see page 12).
Activating the Surround/DSP modes
Available Surround/DSP modes vary depending on the speaker
settings and the incoming signals. For details, see page 33.
settings and the incoming signals. For details, see page 33.
Activating one of the Surround/DSP modes automatically
recalls the memorized settings and adjustments.
recalls the memorized settings and adjustments.
• To adjust the speaker output level, see page 27.
• When activating one of the Surround/DSP modes, you
can adjust CENTER TONE. (see page 29)
• When activating one of the Surround/DSP modes
(except PLIIx MUSIC, PLII MUSIC, NEO:6 MUSIC, and
ALL CH STEREO), you can adjust CENTER ALIGN. (see
page 29)
ALL CH STEREO), you can adjust CENTER ALIGN. (see
page 29)
• When activating NEO:6 MUSIC, you can adjust CENTER
GAIN. (see page 29)
• When activating the DSP mode (except ALL CH
STEREO), you can adjust the following settings:
EFFECT (see page 28)
LIVENESS (see page 28)
ROOM SIZE (see page 28)
LIVENESS (see page 28)
ROOM SIZE (see page 28)
• When activating “PLIIx MUSIC” and “PLII MUSIC,” you
can adjust the following settings:
CENTER WIDTH (see page 29)
DIMENSION (see page 29)
PANORAMA (see page 28)
DIMENSION (see page 29)
PANORAMA (see page 28)
Selecting the Surround/DSP modes
From the remote control:
1
Select and play any source.
• Make sure you have selected the input mode (analog or
digital) correctly.
2
Press SURROUND repeatedly to select the
Surround/DSP mode you want.
Surround/DSP mode you want.
Ex.: When “DOLBY DIGITAL” is selected for Dolby Digital
multi-channel software:
*
1
“AUTO SURROUND” is the initial setting.
*
2
Available Surround modes vary depending on the speaker
settings and the incoming signals. For details, see page
33.
settings and the incoming signals. For details, see page
33.
*
3
If an incoming signal is a multi-channel (2 channel or more)
digital signal, “MONO FILM” is not available.
digital signal, “MONO FILM” is not available.
*
4
If “SURROUND SPK” is set to “
<
NO
>
,” “ALL CH STEREO”
is not available.
To cancel Surround/DSP modes
Press SURROUND repeatedly so that “SURROUND OFF”
appears on the display.
appears on the display.
L
LS
RS
S.WFR LFE
C
R
DIGITAL
DIGITAL AUTO
SURROUND OFF
(Back to the beginning)
Surround modes
*
2
AUTO SURROUND
*
1
HALL1
HALL2
LIVE CLUB
DANCE CLUB
PAVILION
THEATER1
THEATER2
MONO FILM
*
3
ALL CH STEREO
*
4
L
LS
RS
S.WFR LFE
C
R
DIGITAL
DIGITAL AUTO
SURROUND OFF
(Back to the beginning)
Surround modes
*
2
AUTO SURROUND
*
1
HALL1
HALL2
LIVE CLUB
DANCE CLUB
PAVILION
THEATER1
THEATER2
MONO FILM
*
3
ALL CH STEREO
*
4
1
2
1,3
2