Philips 8160xlcc 사용자 설명서
ENGLISH
25
ENGLISH
24
◗ You may quickly rinse the razor heads with
warm water after using the Jet Clean System
to remove any residual cleaning solution.
to remove any residual cleaning solution.
◗ If the razor needs to be recharged, you can
simply leave it in the Jet Clean System after
cleaning and the razor will automatically
recharge.The charge light on the Jet Clean
System will blink to indicate the razor is
recharging.
cleaning and the razor will automatically
recharge.The charge light on the Jet Clean
System will blink to indicate the razor is
recharging.
◗ For optimal razor drying time after cleaning,
remove razor from Jet Clean System after the
cleaning cycle is complete and allow to air dry.
cleaning cycle is complete and allow to air dry.
◗ You may store your razor in the Jet Clean
System. Unplug from the outlet when
charging/cleaning is complete.
charging/cleaning is complete.
Quick Cleaning: Razor Heads
The razor heads may also be quickly cleaned
after each use by rinsing with hot water. Water
from the tap should be on a hot setting, BUT BE
CAREFUL TO TEST WATER FIRST SO AS NOT
TO BURN OR SCALD HANDS.
after each use by rinsing with hot water. Water
from the tap should be on a hot setting, BUT BE
CAREFUL TO TEST WATER FIRST SO AS NOT
TO BURN OR SCALD HANDS.
◗ Regular cleaning guarantees better shaving
results.
◗ Do not immerse razor in water.
C
◗ The tap symbol on the back of the razor
indicates that the razor can be rinsed under
running tap water.
running tap water.
C
◗ While rinsing razor heads, water may drip out
of the base of razor.This is a normal
occurrence.
occurrence.
◗ Do not lift the razor lever or press the
ON/OFF button while the cleaning cycle is
running. If this does occur, the cleaning cycle
will stop and the razor holder will automatically
move to the starting position.The cleaning
cycle can be re-started by pressing the
ON/OFF button once.
running. If this does occur, the cleaning cycle
will stop and the razor holder will automatically
move to the starting position.The cleaning
cycle can be re-started by pressing the
ON/OFF button once.
◗ If the power plug is disconnected before the
cleaning cycle is complete, the razor holder will
remain in its current position. Reconnect the
plug into the outlet or Jet Clean System and the
razor holder will automatically move to the
highest position. The cleaning cycle can be
re-started by pressing the ON/OFF button once.
remain in its current position. Reconnect the
plug into the outlet or Jet Clean System and the
razor holder will automatically move to the
highest position. The cleaning cycle can be
re-started by pressing the ON/OFF button once.
NOTE: If the cleaning solution level drops below
the minimum level during the cleaning cycle, the
cleaning light will blink at intervals and razor
holder returns the razor to the starting position,
stopping the cleaning cycle. Unplug Jet Clean
System from the outlet, remove razor and refill
canister (see “Preparing Jet Clean system for Use”).
the minimum level during the cleaning cycle, the
cleaning light will blink at intervals and razor
holder returns the razor to the starting position,
stopping the cleaning cycle. Unplug Jet Clean
System from the outlet, remove razor and refill
canister (see “Preparing Jet Clean system for Use”).
C
6
When the entire cleaning cycle is complete
and the razor is hygienically clean, the razor
will be raised to the starting position and
the charge light on the Jet Clean System will
blink indicating that the razor is
(re)charging.
and the razor is hygienically clean, the razor
will be raised to the starting position and
the charge light on the Jet Clean System will
blink indicating that the razor is
(re)charging.
C
7
Raise the lever holding the razor to the
highest position (1) and carefully remove
the razor from the Jet Clean System (2).
highest position (1) and carefully remove
the razor from the Jet Clean System (2).