Philips dvdr3400-37b 빠른 설정 가이드

1

Connect

2

Set up

Start with the ‘Basic Connection.’
If you have a Cable Box or Satellite Receiver, follow the instructions for ‘Connection with a 
Cable Box or Satellite Receiver’. 

~

L

R

Television (rear)

To antenna 
or set-top 
box

Philips recorder 
(rear)

R

Philips recorder 
(rear)

A

 

Keep the existing antenna connection from the 
Antenna TV signal to the Cable Box/ Satellite 
Receiver.

B

 

Use an antenna cable to connect the ANTENNA-
IN 

jack on the recorder to the RF OUT jack on 

the Cable Box/Satellite Receiver.

C

 

Follow steps 

C

 to 

E

 under ‘Basic Connections’ 

before you proceed to step 

D

 below. 

   

Note The antenna connection may be different 

 

depending on the Satellite Receiver/Cable Box. 

 

Refer to its user manual for proper antenna 

 connection.

D

 

Use the yellow video cable (not supplied) to 
connect the VIDEO (CVBS) INPUT jack on 
this recorder to the VIDEO OUT jack on the 
Cable Box/ Satellite Receiver.

E

 

Use the audio cable (red/white plugs – not 
supplied) to connect the AUDIO INPUT jack 
on this recorder to the AUDIO OUT jack on the 
Cable Box/ Satellite Receiver.

Philips recorder (front panel)

To AC
power

Basic Connection

Connection with a Cable Box 
or Satellite Receiver

A

  Before connecting, unplug the antenna cable 

that is currently connected to your TV.

B

 

Connect the antenna cable to the ANTENNA-
IN 

jack on the recorder.

C

 

Use the supplied RF coaxial cable to connect the 
TV-OUT 

 jack on this recorder to the 

Antenna In jack on the TV.

D

 

Use the supplied video cable (yellow plug) to 
connect the VIDEO (CVBS) OUTPUT jack on 
this recorder to the VIDEO IN jack on the TV.

E

 

Use the supplied audio/video cable (red/ white 
plugs) to connect the AUDIO OUTPUT jacks 
on this recorder to the AUDIO IN jacks on the 
TV.

F

 

Connect the power cable from the recorder to 
an AC power outlet.

   

Television (rear)

To antenna 
or set-top 
box

B

C

D

E

F

C

D

Cable Box/Satellite Receiver (rear)

A

A

 

Select the video input channel on  

 your TV

A

 Press STANDBY-ON on the 

recorder

B

  Turn on the TV.

   

Note If connected to your VCR, make sure it is 

 

switched off or in standby mode before 

 proceeding.

C

 Press SETUP 

.

D

  Select the TV’s video input channel that 

corresponds to the jacks connecting the 
recorder to the TV. 

   

Note Video Input selection varies for different 

 

brands/models of TVs. Consult the user manual 

 

that came with your TV if none of the below is 

 successful.

 

Press channel 2 on your TV. Then press the 
channel down button to locate the video input 
channel. (This channel is usually located 
between the lowest and highest TV channels.) 

 

OR, for some TVs, there may be a button on 
the TV’s remote control that accesses the video 
input channel labeled SOURCE, AV or SELECT.

 

OR, select the Video Input Channel from the 
TV’s on-screen menu system.

 

   

Note Consult your TV manufacturer if none of 

 

the above is successful.

B

B

 

Initial Installation

A

 Press SETUP 

 on the remote  control.

Screen Saver

Reset Menu Settings

Setup Menu - General

English

On

OK

 

Note Use up S and down T keys to toggle 

 

through the options. Select an item by pressing 

 right 

X.  To confi rm a setting, press OK  .

B

 

Select the OSD language.

 

 

Remain in 

 mode, select  { On Screen 

Display Language } and press  right X to 
access the options. 

  Select the desired language option and 

press OK 

 to confi rm your selection.

C

  

Setup and install TV channels.

 

Highlight 

 and press right X. Select 

{ Tuner Input Source } and press  OK 

.

 

 

 

 

{ Cable } – if the recorder is connected directly 

 

to the cable signal or through a set-top box.

  

{ Air } – if the recorder is connected directly to 

 

an indoor or outdoor antenna.

     

Note Press OK 

 to confi rm your selection.

 

Select { Channel Search } and press OK 

  

on the remote control to start automatic TV    
channel search.

Note If using a cable box/ satellite receiver, 

 

you may only pick up one channel. Leave the 

 

recorder on this channel and change channels at 

 

the cable box or satellite receiver. 

D

 

Set the date and time.

 

 

Highlight 

 and press right X.  

Select { Date (mm/dd/yy) } or 
{ Time (hh:mm:ss) } and press OK 

.

 Use 

the 

numeric keypad 0 

 -9 

 

to input the date/time, then press OK 

 to 

confi rm.

   

Note To further fi ne-tune the date and time 

 

settings, see the user manual “CLOCK Settings”.

E

 

Press SETUP 

 to exit.

E

dvdr3400_37_qsg_eng_22142.indd   2

dvdr3400_37_qsg_eng_22142.indd   2

2006-12-05   10:24:25 AM

2006-12-05   10:24:25 AM