Philips mc-30 사용자 설명서
14
English
3140 115 27913
Tuner
Tuning to radio stations
1
Select TUNER source.
➜ TUNER is displayed briefly.
2
Press BAND once or more to select your
waveband.
waveband.
3
Press down on TUNING
3 or 4 and release
button.
➜ The radio automatically tunes to a station
with sufficient reception. Display indication during
automatic tuning:
➜ The radio automatically tunes to a station
with sufficient reception. Display indication during
automatic tuning:
SEARCH.
➜ If a FM station is received in stereo,
STEREO
is
shown.
4
Repeat step 3 if necessary until you find the
desired station.
desired station.
¶ To tune to a weak station, press TUNING 3 or
4 briefly and repeatedly until you have found
optimal reception.
optimal reception.
Programming radio stations
You can store up to a total of 40 radio stations
in the memory.
in the memory.
Automatic programming
Automatic programming will start with a chosen
preset number. From this preset number
upwards, former programmed radio stations will
be overridden. The system will only programme
stations which are not in the memory already.
Automatic programming will start with a chosen
preset number. From this preset number
upwards, former programmed radio stations will
be overridden. The system will only programme
stations which are not in the memory already.
1
Press PRESET
4 or 3 ( ¡ or ™ on the
remote control) to select the preset number
where programming should start.
where programming should start.
Note:
– If no preset number is selected, default is preset
(1) and all your presets will be overridden.
– If no preset number is selected, default is preset
(1) and all your presets will be overridden.
2
Press PROGRAM on the system or remote
control for more than 2 seconds to activate
programming.
➜ AUTO is displayed and available stations are
programmed in order of waveband reception
strength: FM followed by MW and LW. The last
preset automatically stored will then be played.
control for more than 2 seconds to activate
programming.
➜ AUTO is displayed and available stations are
programmed in order of waveband reception
strength: FM followed by MW and LW. The last
preset automatically stored will then be played.
Manual programming
1
Tune to your desired station (see Tuning to radio
stations).
stations).
2
Press PROGRAM on the system or remote
control to activate programming.
➜
control to activate programming.
➜
PROGRAM
flashes in the display.
3
Press PRESET
4 or 3 (¡ or ™ on the remote
control) to allocate a number from 1 to 40 to
this station.
this station.
4
Press PROGRAM again to confirm the setting.
➜
PROGRAM
disappears, the preset number and
the frequency of the preset station are shown.
5
Repeat the above four steps to store other
stations.
stations.
¶ You can override a preset station by storing
another frequency in its place.
Tuning to preset stations
¶ Press PRESET 4 or 3 ( ¡ or ™ on the
remote control) until the desired preset station
is displayed.
is displayed.
RDS
(some versions only)
Radio Data System is a service that allows
FM stations to show additional information. If
FM stations to show additional information. If
you are receiving a RDS station,
and the
station name are displayed.
When automatic programming is used, RDS
stations will be programmed first.
When automatic programming is used, RDS
stations will be programmed first.
Scrolling through different RDS
information
information
¶ Press RDS briefly and repeatedly to scroll
through the following information (if available):
– Station name
– Programme type such as
– Station name
– Programme type such as
NEWS, SPORT,
POP M ...
– Radio text messages
– Frequency
– Frequency
TUNING
RDS
/ CLOCK
SIDE A/B
VOLUME
SHUFFLE
SOURCE
TIMER ON•OFF
PROGRAM
REPEAT
REV MODE/
BAND
STANDBY-ON
RECORD
M C - 3 0 M I C R O S Y S T E M
iR
FWD á/ë
REW à /í
PRESET
STOP
PLAY•PAUSE
pg 001-021/MC30/22-Eng
12/7/00, 1:33 PM
14