Maytag mah22pdagw0 사용자 설명서

After the door is opened following the completion of a cycle, the 
display indicates the cycle price (unless set for free operation). As 
coins are dropped or debit inputs arrive, the display will change 
to lead the user through the initiation of a cycle.

This is established by setting the cycle price to zero. When this 
happens, “SELECT CYCLE” will appear rather than a cycle price.

After the washer has been installed and plugged in, the display 
will show “0 MINUTES.” Once the washer has been plugged in 
and the washer door opened and closed, the display will show 
the price. In washers set for free cycles, the display will flash 
“SELECT CYCLE.”

NOTE: Not displayed on washer as shown. Message scrolls 
followed by the failure code.

IMPORTANT: Read all instructions before operating.

■

PD Models: Insert access door key, turn, and lift to remove  
access door. 

■

PN Models: Remove connector AA1 on the circuit board. 

Set-up procedures can be entered by using the Service Access 
Code for PN washers without a key switch installed.

IMPORTANT: Unplug washer or disconnect power before 
opening the console. To access connector AA1:

   Unplug washer or disconnect power.

   Open console, disconnect plug on AA1, close console.

   Plug in washer or reconnect power.

The washer is now in the set-up mode. The lower fabric setting 
key pads and the digital display are used to set up the controls. 
The display can contain 4 numbers and/or letters and a decimal 
point. These are used to indicate the set-up codes and related 
code values available for use in programming the washer.

Once the washer has been programmed with a hand held device 
using Accu Trac, or a Gen. 2 card reader has been installed, the 
washer will be put into dAS mode permanently, and dAS will be 
displayed every time set-up mode is accessed.

1. The PERMANENT PRESS key pad is used to adjust the 

 

values associated with set-up codes. Pressing this key pad 

 

will change the value by increments. Rapid adjustment 

 

is possible by holding the key pad down.

2. The WOOLENS key pad advances you through the set-up 

codes. Pressing this key pad will advance you to the next 
available set-up code. Holding the key pad down will 
automatically advance through the set-up codes at a rate 

 

of 1 per second.

3. The DELICATES & KNITS key pad is used to select or 

deselect options.

NOTE: Prior operation, a payment system or an OPL kit must be 
installed.

Before proceeding, it is worth noting that, despite all of the 
options available, an owner can simply choose to un-crate a new 
commercial washer, hook it up, plug it in, and have a washer that 
operates. Washers are preset at the factory for a 14-minute wash 
period and 3 rinses (no extra rinse). 

■

The WOOLENS key pad will advance you from code to code.

■

The PERMANENT PRESS key pad will change the code 
value. 

■

The DELICATES & KNITS key pad will select or deselect 
options.

FOR PN MODELS: The set-up codes are the same as for the 
“PD” model except where noted.

The set-up code is indicated by the one or two left-hand 
characters. The set-up code value is indicated by the two or 
three right-hand characters. 

6 07

6 

6

07

 

 

 

 

00
 

 

 

 

Represents the number of coins (Coin 1) needed to 
start the washer; may adjust from 0-39. (See 
VALUE OF COIN 1.) Advance from 0-39 by 
pressing PERMANENT PRESS key pad. Factory 
default of 7 x coin 1.

PN MODELS ONLY: Factory default for 0 coins.

With coin slide activation, this represents the 
number of push-in actuations of a coin slide to start 
the washer.

6 01 setting would represent one coin slide 
actuation.

NOTE: For coin slide activation, replacement of the 
meter case is necessary. 

Press the WOOLENS key pad once to advance to 
next code.

7 14

7 14

 

 

 

This is the number of minutes for WASH. Washer 
comes from the factory preset with 14 minutes. 
Choose from 9-17 minutes by pressing the 
PERMANENT PRESS key pad. 

Press the WOOLENS key pad once to advance 

 

to next code.