Maytag w10117890a 사용자 설명서
5
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. The parts supplied are in the
washer basket.
washer basket.
Tools needed for connecting the drain hose and water inlet hoses:
Parts supplied:
Tools needed for securing the drain hose and leveling the washer:
Parts supplied:
Alternate Parts
Your installation may require additional parts. For information on ordering, please refer to the
toll-free phone numbers on the front page of the Use and Care Guide.
toll-free phone numbers on the front page of the Use and Care Guide.
Location Requirements
Selecting the proper location for your washer improves performance and minimizes noise and
possible washer “walk.”
Your washer can be installed in a basement, laundry room, closet, or recessed area. See
“Drain System.”
IMPORTANT: Do not install or store the washer where it will be exposed to the weather.
Proper installation is your responsibility.
You will need:
possible washer “walk.”
Your washer can be installed in a basement, laundry room, closet, or recessed area. See
“Drain System.”
IMPORTANT: Do not install or store the washer where it will be exposed to the weather.
Proper installation is your responsibility.
You will need:
■
A water heater set to deliver 120°F (49°C) water to the washer.
■
A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is
attached to the back of the washer. See “Electrical Requirements.”
attached to the back of the washer. See “Electrical Requirements.”
■
Hot and cold water faucets located within 3 ft (91 cm) of the hot and cold water fill
valves, and water pressure of 5-100 psi (34.5-690 kPa). Washers with triple dispensers
require 20-100 psi (138-690 kPa) for best performance.
valves, and water pressure of 5-100 psi (34.5-690 kPa). Washers with triple dispensers
require 20-100 psi (138-690 kPa) for best performance.
■
A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the
washer on carpeting is not recommended. Ventilation openings in the base must not be
obstructed by carpet.
washer on carpeting is not recommended. Ventilation openings in the base must not be
obstructed by carpet.
■
A sturdy floor to support the washer weight (washer, water and load) of 315 lbs (143 kg).
Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can
remain in the washer and can cause damage in low temperatures. See “Washer Care” for
information on winterizing.
remain in the washer and can cause damage in low temperatures. See “Washer Care” for
information on winterizing.
■
Pliers that open to 1
⁹⁄₁₆"
(3.95 cm)
■
Flat-blade screwdriver
■
Flashlight (optional)
A. Water inlet hose (2)
B. Drain hose form
C. Drain hose extension
D. Drain hose coupling
E. Large flat washer (4)
F. Small flat washer (2)
F. Small flat washer (2)
G. Inlet hose adapter
H. Hose clamp (2)
H. Hose clamp (2)
■
Adjustable or open end
wrench
wrench
⁹⁄₁₆" (14 mm)
■
Level
■
Wood block
■
Ruler or measuring tape
A. Beaded tie strap
B. Front leveling feet with nuts (2)
A
B
C
D
E
F
G
H
A
B
If You Have:
You Will Need to Buy:
Laundry tub or standpipe
taller than 96" (2.4 m)
taller than 96" (2.4 m)
Sump pump system (if not already available)
Overhead sewer
Standard 20 gal. (76 L) 39" (99 cm) tall drain tub or utility
sink, sump pump and connectors (available from local
plumbing suppliers)
sink, sump pump and connectors (available from local
plumbing suppliers)
Floor drain
Siphon break kit, Part Number 280129; additional drain
hose, Part Number 3357090
hose, Part Number 3357090
Water faucets beyond reach
of fill hoses
of fill hoses
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
Drain hose too short
Drain hose kit, Part Number 280131
Lint clogged drain
Drain protector, Part Number 367031