Crestron clw-dim1 dims1 slvd1 사용자 설명서

  

 

5.  Push all power wires back into the wallbox and 

fasten the devices to their respective wallboxes 
with the provided screws. 

6. Attach 

decorative faceplates. 

7.  Restore power at the circuit breaker. 

The -DIM1, -DIMS1, and -SLVD1 have one large 
pushbutton. The -DIM1 and -DIMS1 also have a three-
position mode selection switch. The function of the 
pushbutton is determined by the position of the mode 
selection switch. Refer to the following diagram. 

NOTE:  The -SLVD1 does not have a mode selection 
switch. It emulates the operation of the -DIMS1 to which 
it is connected unless the mode selection switch of the 
master is set to “OFF”. 

Button

Mode Selection Switch
(-DIM1 & -DIMS1 Only)

 

When the mode selection switch is in the “OFF” position, 
the pushbutton will not have any function and the load is 
disconnected from the power source. This must be used 
when changing light bulbs to ensure that the load is fully 
disconnected from power. 

When the mode selection switch is in the “ADJ” position, 
the pushbutton is used to switch between the “Preset 1-
High” and “Preset 1-Low” presets (typically “On” and 
“Off”) as well as adjust the lighting level. Tap the 
pushbutton to fade up or down to either of the two preset 
lighting levels. Tap the pushbutton while the lighting 
level is fading to jump directly to the preset lighting level 
without fading. (i.e., tapping while the lighting level is 
fading up will jump to the “Preset 1-High” level without 
fading, tapping while the lighting level is fading down 
will jump to the “Preset 1-Low” level without fading). 
While the light is off, double-tap the pushbutton to jump 
directly to the “Preset 1-High” lighting level without 
fading. 

The lighting level can be adjusted by pressing and holding 
the pushbutton. After a ½ second, the lighting level will 

ramp up or down. The lighting level will stop at 
maximum brightness (100%) if the lighting level was 
ramping up or minimum brightness (0%) if the lighting 
level was ramping down. To continue ramping the 
lighting level in the opposite direction, release the 
pushbutton, then press and hold the pushbutton again. 

When the desired lighting level is reached, release the 
pushbutton.  

If the lighting level is to be stored as a preset, move the 
mode selection switch to the PRE position. Press and hold 
the pushbutton until the LED flashes. 

NOTE:  Before storing a preset, the lighting must be 
adjusted to the desired level while in the ADJ mode. 

When the switch is in the PRE position, it is in the preset 
mode and can be used to recall and/or store preset lighting 
levels. The pushbutton is used to recall and/or store the 
“Preset 1-High” and “Preset 1-Low” presets. Pressing and 
releasing the pushbutton will fade to the preset lighting 
level over a preset amount of time*. Tapping the 
pushbutton while the light is fading will cause the light 
level to “jump” directly to the preset without fading. 
Pressing and holding the pushbutton until the LED flashes 
will store the current lighting level. 

*  The preset fade time can only be adjusted through Crestron 

programming software. 

To store preset values for “Preset 1-High” and “Preset 1-
Low”; while in the PRE mode, recall the lighting level to 
be changed. Switch to the ADJ mode and adjust the 
lighting to the desired level. Move the mode selection 
switch to PRE. Press and hold the pushbutton until the 
LED flashes to store the new preset value. 

NOTE:  If a new preset value for “Preset 1-High” is 
lower than the stored value for “Preset 1-Low”, the 
previously stored value for “Preset 1-Low” becomes 
“Preset 1-High”. Similarly, if a new preset value for 
“Preset 1-low” is higher than the value stored for “Preset 
1-High”, the previously stored value for “Preset 1-High” 
becomes “Preset 1-Low”. 

NOTE:  The default preset light values for each preset 
are:  

•  Preset 1-High: 100% 
•  Preset 1-Low: 0% 

NOTE:  The device may be warm to the touch during 
operation. This is normal. 

•  Stand Alone Wall Box Dimmer :  CLW-DIM1, DIMS1, & SLVD1