ONKYO TX-DS787 사용자 설명서
27
TUNING
UP
DOWN
FM MUTE /
MODE
DISPLAY
STEREO
CHARACTER /
MEMORY
DIRECT
THX
SURROUND
BASS /
TREBLE
EXIT
MENU
LISTENING MODE
ZONE 2 VOL
CH LEVEL
FM
AM
PHONO
C D
TAPE
DVD
VIDEO
3
VIDEO
4
VIDEO
2
VCR
2
VIDEO
1
VCR
1
STANDBY/ ON
POWER
ANDBY
ST
ZONE
2
OFF
ON
REC OUT
ZONE
2
PHONES
AV RECEIVER
TX-DS
787
MASTER VOLUME
VIDEO
AUDIO
L
R
VIDEO CAM INPUT
/
4
VIDEO
S VIDEO
AUDIO SELECTOR
PUSH TO ENTER
SMART SCAN
CONTROLLER
DSP/ PRESET
POWER
STANDBY/ON
OPEN/CLOSE
REC
AUDIO
MUTING
DISC
TRACK
DVD
CD
PH
TUN
T2
T1
V1
STEREO
1
2
3
6
5
4
7
+ 10
0
ENT
8
9
SURROUND
THX
DSP
LEVEL +
CH SEL
Re-EQ
LEVEL –
DIMMER
HOME THEATER CONTROLLER
RC-390M
LATE NIGHT
DIRECT
DSP
V2
V3
V –
ON
AUDIO MODE
STNBY
/ DTS
PTY/ TP
STANDBY indicator
SEND/LEARN
indicator
Connecting the power
Turning the power on from the remote controller:
Before you can use the remote controller, you must perform steps
1 and 2 above and place the TX-DS787 in the standby state.
1 and 2 above and place the TX-DS787 in the standby state.
1. Press the AUDIO MODE button.
2. Press the ON button to turn on the TX-DS787
(take it out of the standby state).
• To return the TX-DS787 to the standby state, press the
STNBY button.
Connecting the power
• The TX-DS787 is shipped with the main power (POWER)
switch in the on position (
ON
). When the power cord is
plugged in for the first time, the TX-DS787 will automatically
enter the standby state and the STANDBY indicator will light
(same condition after step 2 below).
enter the standby state and the STANDBY indicator will light
(same condition after step 2 below).
• Before you plug in the TX-DS787, confirm that all
connections have been made properly.
• Turning on the power may cause a momentary power surge,
which might interfere with other electrical equipment on the
same circuit, such as computers. If this happens, use a wall
outlet on a different circuit.
same circuit, such as computers. If this happens, use a wall
outlet on a different circuit.
1. Plug the power cord into an AC wall outlet.
2. Press the POWER switch to set the TX-DS787
to standby state.
The STANDBY indicator will light up.
3. Press the STANDBY/ON button to turn on the
TX-DS787. The display will light up and the
STANDBY indicator will turn off.
STANDBY indicator will turn off.
If you press the STANDBY/ON button again, the receiver
returns to Standby mode.
returns to Standby mode.
Memory preservation
This unit does not require memory preservation batteries. A
built-in memory power backup system preserves the contents
of the memory during power failures and even when the
POWER switch is set to off. The POWER switch must be set
to on in order to charge the backup system.
built-in memory power backup system preserves the contents
of the memory during power failures and even when the
POWER switch is set to off. The POWER switch must be set
to on in order to charge the backup system.
The memory preservation period after the unit has been
turned off varies depending on climate and placement of the
unit. On the average, memory contents are protected over a
period of a few weeks after the last time the unit has been
turned off. This period is shorter when the unit is exposed to a
highly humid climate.
turned off varies depending on climate and placement of the
unit. On the average, memory contents are protected over a
period of a few weeks after the last time the unit has been
turned off. This period is shorter when the unit is exposed to a
highly humid climate.
To wall outlet