Hitachi 42pd7500a 사용자 설명서
21
BASIC OPERATION (continued)
INPUT SELECT button
CHANNEL UP/DOWN buttons
Input Switching
Size Switching
• Input can be switched by pressing the AV1~5, RGB1 or
RGB2 buttons of the remote control.
• Input can be switched to TV by pressing CHANNEL
UP/DOWN buttons or PROGRAMME SELECT buttons.
• Input can be switched between TV and DTT by pressing
DTT/TV button of the remote control.
• Input can be switched in the sequence of DTT
➝ TV ➝
AV1
➝ AV2 ➝ AV3 ➝ AV4 ➝ AV5 ➝ RGB1 ➝ RGB2 by
pressing the INPUT SELECT button of the control panel.
Each time the ZOOM button of the remote control is
pressed, the screen display size will change in sequence
and the status will be displayed at the bottom of the screen.
pressed, the screen display size will change in sequence
and the status will be displayed at the bottom of the screen.
• During VIDEO signal input (AV3, AV4, AV5, RGB1 (set
to [DVI-STB]) and RGB2 (set to [Component]))
• The size will be fixed as Full mode and not change when receiving
the component signal of 1080i/50, 1080i/60, 720p/50 or 720p/60.
• During DTT mode
• [Auto] depends on the programme being broadcast but does not
link to Default Zoom setting in the Function Menu.
• During AV1~ AV2 signal input
• [Auto] is the mode using the Switch signal from the equipment
connected to AV1~AV2 terminal included in SCART connector
No.8 pin which indicate the picture format of the video source.
When Switch signal has not been detected, Default Zoom setting
in the Function Menu is used to choose.
No.8 pin which indicate the picture format of the video source.
When Switch signal has not been detected, Default Zoom setting
in the Function Menu is used to choose.
• During TV mode
• [Auto] is the mode using WSS (Wide Screen Signals) which identify
the picture format movies and programmes are broadcast in.
Various broadcast stations now transmit WSS. It can be detected
and the monitor automatically switch to the correct format.
However, some broadcasters do not transmit WSS, so this monitor
will not recognize which format is being transmitted. Therefore,
Default Zoom setting in the Function Menu is used to choose when
a WSS has not been sent or has not been detected.
Various broadcast stations now transmit WSS. It can be detected
and the monitor automatically switch to the correct format.
However, some broadcasters do not transmit WSS, so this monitor
will not recognize which format is being transmitted. Therefore,
Default Zoom setting in the Function Menu is used to choose when
a WSS has not been sent or has not been detected.
DTT TV AV1 AV2 AV3
RGB2 RGB1 AV5 AV4
Panoramic 4:3 Full
14:9Zoom C14:9L Zoom
Full
INPUT SELECT
buttons
RECALL button
ZOOM button
Display size selection diagram
When you want to
Set the display size to
Input signal
Display screen
Remarks
Play a 4:3 image in a 16:9 screen faithfully.
4 : 3
(4:3 signal)
Blanking occurs on both sides.
Play a 4:3 image in a 16:9 screen with the
height and width of the middle of the
screen enlarged on equal scales and with
both sides appearing somewhat enlarged.
height and width of the middle of the
screen enlarged on equal scales and with
both sides appearing somewhat enlarged.
Panoramic
Play a 16:9 VISTA size image in the 4:3
image faithfully reproduced on the 16:9
screen.
image faithfully reproduced on the 16:9
screen.
Zoom
(Vista)
• The 4:3 image is called a letterbox image.
• In some cases, some slight blanking may
• In some cases, some slight blanking may
remain at the top and bottom.
Play a 4:3 image faithfully in a 16:9 screen
in the standard vertical size and horizontal-
ly squeezed.*
in the standard vertical size and horizontal-
ly squeezed.*
Full
(Squeeze)
* An image with an aspect ratio of 16:9 shrunk
horizontally to 4:3 to display in a 4:3 screen.
CHANNEL
UP/DOWN button
UP/DOWN button
PROGRAMME
SELECT buttons
SELECT buttons
Auto Full Zoom
14:9Zoom C14:9L
Auto Full Zoom
14:9Zoom C14:9L
Auto Full