Dynex DX-TVM112 사용자 설명서

Low-Profile TV Mount

DX-TVM112

Thank you for choosing the Dynex DX-TVM112. The DX-TVM112 TV 
mount is designed to support a TV weighing up to 50 lbs. (22.7 kg).

A  Wall plate (1)
B  Left TV bracket (1)
C  Right TV bracket (1)
M4 bag
 D M4 x 12 mm screws (4)
 E M4 x 30 mm screws (4)
 

F  M4 spacers (4)

 

G  M4 washers (8)

M6 bag
 H 

M6 × 12 mm screws (4)

 I M6 × 20 mm screws (4)
 J M6 × 35 mm screws (4)
 

K  M6 spacers (4)

 

L  M6 washers (4)

Lag bolt bag
 

M  Wall anchors (3)

 

N  5/16 in. (7.9 mm) washers (3)

 O 5/16 

in. × 2 ½ in. lag bolts (3)

  Option 1: Attaching to a TV with a flat back surface
  Attach the left and right TV brackets (B and C) to the back of the TV using:
  The M4 washers (G) and the M4 screws (D).
 Or
  The M6 washers (L) and the M6 screws (H or I).

• Power 

drill

•  3/16 in. wood drill bit
•  ½ in. masonry drill bit
• Phillips 

screwdriver

• Level
•  Socket wrench with ½ in. socket or 
 adjustable 

wrench

• Pencil
• Stud 

finder

• Awl

1  Locate the stud. Verify the center of the stud with an awl or thin nail or 

   

use an edge to edge stud finder.

2  Level the wall plate (A) and mark the hole locations.
3  Drill the pilot holes as illustrated.
4  Align the wall plate (A) with the pilot holes, then place the washers (N) over 

   

the holes. Insert the lag bolts (O) through the washers, then tighten the lag 

   

bolts only until the washers are pulled firmly against the wall plate. 

   

DO NOT over-tighten the lag bolts (O).

CAUTION: Avoid potential injuries or property damage!
Any material covering the wall must not exceed 5/8 in. (16 mm).

  Option 2: Attaching to a TV with a rounded back surface
  Attach the left and right TV brackets (B and C) to the back of the TV using:
  The M4 spacers (F), M4 washers (G), and the M4 screws (E).
 Or 
  The M6 spacers (K), M6 washers (L), and the M6 screws (J).

M4

M4

M6

M6

5/16 in.

5/16 × 2½ in.

M4 × 12 mm

M4 × 30 mm

M6 × 12 mm

M6 × 20 mm

M6 × 35 mm

or

or

or

or

5/8 in.

(<16 mm)**

2.5 in.

(63.5 mm)*

*Drill the pilot hole to a depth of 2.5 in. (63.5 mm)
**Maximum thickness of any material covering 
  the stud or concrete surface.

NOTE: Determine if there is sufficient space between the back of 
the TV and the wall to connect all your cables before proceeding. 
You may need to use the optional spacers to allow more clearance 
between the back of the TV and the wall.

or

or

or

NOTE: Adjust to shorten 
or hide the cords