Fagor 8025 t cnc 사용자 설명서
- 5 -
Operating mode selected at the CNC (B8-11 REG121 at the PLCI, Not available at the PLC64)
Status of the miscellaneous "M" functions (REG122 at the PLCI, Not available at the PLC64)
The status of each one of these functions is given by a bit and will appear as a "1" when active and "0" when inactive.
2. 4TH AXIS NOW AVAILABLE ON 8025T MODELS
From this version on, this feature is now available on all these models:
CNC-8025T (not available until now)
CNC-8025TG
CNC-8025TS
CNC-8025TI (not available until now)
CNC-8025TGI
CNC-8025TSI
3. SPINDLE SPEED DISPLAY UNITS
Until now, the spindle speed was always displayed in rpm. From now on, the display units may be selected by means
of machine parameter "P621(6)".
of machine parameter "P621(6)".
P621(6) = 0
In rpm when operating in RPM and in m/min. (ft./min.) when at Constant Surface Speed.
P621(6) = 1
Always in rpm, even when operating at Constant Surface Speed.
4. SINGLE BLOCK TREATMENT
The CNC considers a "Single block" the group of blocks between a G47 and a G48.
After executing function G47, the CNC executes all the following blocks until executing a block containing function
G48 even when in Single Block mode.
G48 even when in Single Block mode.
If
is pressed while executing a "single block" in Automatic or Single-Block mode, the CNC keeps executing
the rest of the blocks until it runs into a G48 and it, then, interrupts program execution.
While function G47 is active, the Manual Feedrate Override switch and the spindle speed override keys will be disabled,
thus the program will be executed at 100% of the programmed F and S values.
thus the program will be executed at 100% of the programmed F and S values.
Functions G47 and G48 are modal and incompatible with each other.
On power-up, after executing an M02/M30, after an EMERGENCY or a RESET, the CNC assumes G48.
5. TWO ELECTRONIC HANDWHEELS ARE NOW POSSIBLE
From this version on, up 2 electronic handwheels may be used one for the X axis and another one for the Z axis. The
4th axis and the Live Tool will no longer be available. The feedback inputs will be used as follows:
4th axis and the Live Tool will no longer be available. The feedback inputs will be used as follows:
A1 - X axis; A2 - Z axis handwheel; A3 - Z axis; A4 - 3rd axis or "C" axis; A5 - Spindle; A6 - X axis handwheel
The handwheels will be operative when selecting the JOG mode. One of the handwheel positions must also be selected
at the Manual Feedrate Override switch of the operator panel.
at the Manual Feedrate Override switch of the operator panel.
The possible positions are: 1, 10 and 100, which indicate the multiplying factor applied to the pulses coming from the
electronic handwheel.
electronic handwheel.
B8
B9
B10
B11
0
0
0
0
Automatic
0
0
0
1
Single block
0
0
1
0
Play-Back
0
0
1
1
Teach-in
0
1
0
0
Dry-Run
0
1
0
1
JOG
0
1
1
0
Editor
0
1
1
1
Peripherals
1
0
0
0
Tool Table and G functions
1
0
0
1
Special modes
B15 B14 B13 B12 B11 B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
M44 M43 M42 M41
M19 M1 M30
M4
M3
M2
M0