Carvin rl810t 사용자 설명서
SPEAKER CABLES
12 gauge
Speakon™ speaker cables will provide a secure connection and high cur-
rent transfer of power to the speakers. You can also use standard 1/4" speaker
cables instead of the
cables instead of the
Speakon™ cables provided they are at least 16 gauge. You can
DAISY-CHAIN up to one additional speaker per cable by using the unused OUTPUT
jack (right side) on your speaker jack plate. Be sure to note the total impedance to
the amp so it is not lower than it’s recommended impedance.
See Typical Loudspeaker Impedance Configurations.
jack (right side) on your speaker jack plate. Be sure to note the total impedance to
the amp so it is not lower than it’s recommended impedance.
See Typical Loudspeaker Impedance Configurations.
PRECAUTIONS
1) DO NOT EXCEED THE POWER RATING marked on the rear connect plate.
Excessive power will destroy drivers. 2) DISTORTION from power amps will destroy
drivers much faster than clean power. 3) WATER, MOISTURE, and DUST are harm-
ful to drivers causing failure which is not covered under warranty.
drivers much faster than clean power. 3) WATER, MOISTURE, and DUST are harm-
ful to drivers causing failure which is not covered under warranty.
WARRANTY
CARVIN loudspeakers are covered by a ONE year limited warranty unless otherwise
stated. Warranty coverage is limited to original manufactures defects only. WAR-
RANTY DOES NOT COVER: 1) Opened or burned voice coils. 2) Torn cones caused
by improper packing or abuse. 3) Damage from rain, moisture, ETC. When return-
ing defective driver(s), remove them from the enclosure to reduce shipping costs.
DO NOT stuff paper into the driver(s). Return pre-paid by UPS. Include your address
and description of the problem. Your driver(s) will be returned COD for the cost of
shipping and reconditioning if not covered under warranty.
RANTY DOES NOT COVER: 1) Opened or burned voice coils. 2) Torn cones caused
by improper packing or abuse. 3) Damage from rain, moisture, ETC. When return-
ing defective driver(s), remove them from the enclosure to reduce shipping costs.
DO NOT stuff paper into the driver(s). Return pre-paid by UPS. Include your address
and description of the problem. Your driver(s) will be returned COD for the cost of
shipping and reconditioning if not covered under warranty.
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
CARVIN ENGINEERING DATA
RL810T BASS SPEAKER SYSTEM
INSTRUCTIONS
The RL810T is an eight-10” speaker system designed for the professional who
wants the absolute best in bass guitar amplification. With 8 heavy duty ten inch
woofers and an adjustable 1” Titanium HF Driver, your sound will be crisp and clear
even at the highest sound pressure levels. You will get clean, punchy, uncolored bass
reproduction from an all new cabinet & cross-over design. The Duratuff II™ covered
cabinet is 18 inches deep and is “front shelf” ported for a full, deep sound that defi-
nitely does “Boom” into any room!
The built-in heavy-duty casters and top handles makes moving the RL810T easy.
Just rock it back and roll it off stage.
woofers and an adjustable 1” Titanium HF Driver, your sound will be crisp and clear
even at the highest sound pressure levels. You will get clean, punchy, uncolored bass
reproduction from an all new cabinet & cross-over design. The Duratuff II™ covered
cabinet is 18 inches deep and is “front shelf” ported for a full, deep sound that defi-
nitely does “Boom” into any room!
The built-in heavy-duty casters and top handles makes moving the RL810T easy.
Just rock it back and roll it off stage.
RECEIVING INSPECTION
INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during ship-
ping. If any damage is found, please notify the shipping company & CARVIN.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship your
unit, always use the original carton and packing material. This will provide the best pos-
sible protection during shipment. CARVIN and the shipping company are not liable for
any damage caused by improper packing.
sible protection during shipment. CARVIN and the shipping company are not liable for
any damage caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped sepa-
rately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this man-
ual for your records. Keep your portion of the card and return the portion with your name
and comments to us.
and comments to us.
TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS
Individual speaker or speaker cabinet wiring examples for total impedance.
SERIES CONNECTION
16Ω TOTAL IMPEDANCE
+
+
+
PARALLEL CONNECTION
4Ω TOTAL IMPEDANCE
+
+
+
8Ω TOTAL
IMPEDANCE
SERIES/PARALLEL
CONNECTION
8Ω TOTAL IMPEDANCE
+
+
+
+
+
+
+
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
8Ω
4Ω
8Ω
8Ω
16Ω
8Ω
8Ω
REAR CONNECT PLATE
Two standard 1/4" phone
jacks and two high current
Speakon™ connectors are fea-
tured. One for connecting to
the power amp and the other
for connecting to an additional
speaker system.
Speakon™ connectors are fea-
tured. One for connecting to
the power amp and the other
for connecting to an additional
speaker system.
76-00810B 0705
12340 World Trade Drive, San Diego, CA 92128
800.854.2235 www.carvin.com
Accepts
Speakon™
&1/4” cables
RL810T
HORN ATTENUATION SWITCHES
The rear crossover panel features a high frequency
attenuator to control the volume of the 1” Titanium HF
Driver. This will allow you to cut high frequencies in
3dB increments to customize the cabinet output.
Driver. This will allow you to cut high frequencies in
3dB increments to customize the cabinet output.
MODEL RL810T BASS SPEAKER SYSTEM SPECS:
Frequency Response:
60 to 16k Hz
Drivers:
Eight 10” PS10 Woofers & one 1” Titanium HF Driver
Power Handling:
1200 watts
Horn Attenuation:
Switch attenuation (reduction) in 3dB steps
Horn Protection:
Yes—Maintenance Free
Coverage Angles:
90° Horizontal, 90° Vertical
Nominal Impedance:
4
Ω
Input Connector:
One 1/4" Phone Connector/one Speakon™
Output Connector:
One 1/4" Phone Connector/one Speakon™
Woofer Enclosure Type:
Vented Box
Enclosure Covering:
Duratuff II™
Dimensions:
47.75"W x 18.25"D x 23.5"H
Warranty:
One Year
Weight:
118 lbs.
Casters:
Casters included