ge-interlogix simon 3 사용자 설명서
Simon Security System
7
X10 Modules
The system can control up to 8 individual unit numbers on Lamp, Wall switch, Appli-
ance, and Universal Modules.
ance, and Universal Modules.
House Code and Unit Numbers
Each device (lamp, appliance, etc.) controlled by the panel must have an identification
setting. The modules use two dials to set identification codes: one with letters A through
P and one with numbers 1 through 16.
setting. The modules use two dials to set identification codes: one with letters A through
P and one with numbers 1 through 16.
The lettered dial sets the house code, which enables the system to differentiate this
home from other homes in the area. Set all modules (except the remote siren) and the
panel to the same house code.
home from other homes in the area. Set all modules (except the remote siren) and the
panel to the same house code.
Note
All Lamp Modules with the
same house code will turn
on or flash as a group during
an alarm or when operating
the “Light” button on a Key-
chain Touchpad.
All Lamp Modules with the
same house code will turn
on or flash as a group during
an alarm or when operating
the “Light” button on a Key-
chain Touchpad.
The numbered dial sets the unit number, which identifies and lets you control a specific
device. Each device must have a unique unit number (1-8) to be individually controlled.
For example, lights and appliances operated from a Remote Handheld Touchpad or
operated by a sensor; or lights programmed to go on during the entry/exit delay or at
scheduled times.
device. Each device must have a unique unit number (1-8) to be individually controlled.
For example, lights and appliances operated from a Remote Handheld Touchpad or
operated by a sensor; or lights programmed to go on during the entry/exit delay or at
scheduled times.
Note
When unit numbers 9-16 are used for lamp modules, they can only be controlled by an all on
or all off command. A lamp will flash to the arming level if its unit number is set to 10. A lamp
set to unit number 10 will flash once if the panel is disarmed, twice if doors & windows are
armed, etc. The remote siren can be set to any unit number to hear alarm sounds. Set it to
unit number 9 to also hear arming level beeps, status beeps, and trouble beeps. Do not use a
lamp module to control appliances. Use an appliance module, since the wattage rating on
Lamp Modules is less than on Appliance Modules.
When unit numbers 9-16 are used for lamp modules, they can only be controlled by an all on
or all off command. A lamp will flash to the arming level if its unit number is set to 10. A lamp
set to unit number 10 will flash once if the panel is disarmed, twice if doors & windows are
armed, etc. The remote siren can be set to any unit number to hear alarm sounds. Set it to
unit number 9 to also hear arming level beeps, status beeps, and trouble beeps. Do not use a
lamp module to control appliances. Use an appliance module, since the wattage rating on
Lamp Modules is less than on Appliance Modules.
¾
To Fill Out the Home Control Planning Table:
Note
The house code instructions
that come with the Power-
horn Siren won’t work with
this panel. Follow the house-
code instructions given here.
The house code instructions
that come with the Power-
horn Siren won’t work with
this panel. Follow the house-
code instructions given here.
1.
Set the house code on all modules (except the remote siren) to the same letter.
2.
Set the Remote Siren house code to the next alphabetical letter. For example, if you
chose house code B in step 1 above, set the remote siren house code to C.
chose house code B in step 1 above, set the remote siren house code to C.
3.
Set the module unit numbers.
Note
If you are using a Universal
Module to operate a device,
make sure to assign a
unique unit number to this
module, choosing from 1-8.
If you are using a Universal
Module to operate a device,
make sure to assign a
unique unit number to this
module, choosing from 1-8.
4.
List the location of the lamp or appliance in the Location column of the Home Con-
trol Planning Table.
trol Planning Table.
5.
Write the location of each Lamp Module on an adhesive note and label the module.
6.
Decide if the device should be activated by sensors, entry/exit delay, time, or a
combination. An example of sensor activation is using a motion sensor to turn on a
light. Record the information in the appropriate columns.
combination. An example of sensor activation is using a motion sensor to turn on a
light. Record the information in the appropriate columns.
Use the following tables to help you further plan X10 module installation.
X10 House Code Assignments
X10 Device
Settings
Lamp, Appliance, Universal
Set all modules to the same house code (A
- P) except the remote sirens.
Remote Siren
House code must be set to the next higher
alphabetical letter.