Panasonic PPDTH42LRG20B 작동 가이드

Frequently Asked 

Questions

 

71

Set “P-NR” in the Picture Menu (to remove noise). (p. 28)

 

Check nearby electrical products 

 

(fluorescent lamp, DECT phones, mobile phones, microwave, etc.).

Is “Contrast”, “Brightness” or “Colour” in the Picture Menu set to the 

 

minimum? (p. 28)
Please also refer to “Neither image nor sound is produced” (p. 70)

 

(no sound or low volume)

Reset channels. (p. 36 and p. 37)

 

Please also refer to “Neither image nor sound is produced” (p. 70)

 

Turn the TV Off with Mains power On / Off switch, then turn it On again.

 

If the problem persists, perform “Shipping Condition” (p. 46).

 

Is “Sound mute” active? (p. 8)

 

Is the volume set to the minimum?

 

Is Speaker Selection (VIERA Link) set to “TV”?

 

Please also refer to “Neither image nor sound is produced” (p. 70)

 

Sound signal reception may be deteriorated.

 

Set “NICAM” (p. 29) in the Sound Menu to “Off”. (Analogue only)

 

Please also refer to “Neither image nor sound is produced” (p. 70)

 

Reset channels. (p. 36 and p. 37)

 

Check the digital transmission by contacting Digital UK on 

 

08456 50 50 50 or at www.digitaluk.co.uk
Check the analogue broadcast (if still available in your area).

 

Consult an aerial engineer to check the alignment of your aerial.

 

The channel may broadcast for part of the day.

 

Check the channel in the TV Guide. (p. 18 and p. 19)

 

Channel position numbers may be changed by broadcasters.

 

Reset channels. (p. 36 and p. 37)

 

Set the sound setting of the connected equipment to “2ch L.PCM”.

 

Check the “HDMI1 / 2 Input” setting in the Sound Menu. (p. 29)

 

If digital sound connection has a problem, select analogue sound 

 

connection. (p. 68)

Check the HDMI cable is connected properly. (p. 64 and p. 65)

 

Turn the TV and equipment Off, then turn them On again. (p. 59)

 

Check an input signal from the equipment. (p. 69)

 

Check the output resolution from the equipment. (p. 69)

 

Use an equipment compliant with EIA/CEA-861/861B.

 

Press and hold the standby On / Off switch on the remote control 

 

for about 1 second if Power LED is red.
Check the mains lead is plugged into the socket.

 

The fuse in the mains plug may have blown. Replace it with one of 

 

an identical rating (p. 4). 

Auto power standby function is activated. (p. 9)

 

The TV enters Standby mode about 30 mins. after analogue 

 

broadcast ends.

Are the batteries installed correctly? (p. 6)

 

Has the TV been switched On?

 

The batteries may be running low. Replace them.

 

Point the remote control directly at the front of the TV (within about 

 

7 m and a 30 degree angle of the front of the TV).
Situate the TV so that sunshine or other sources of bright light do 

 

not shine on the TV’s remote control signal receiver.

Even when the temperature of parts of the front, top and rear 

 

panels has risen, these temperature rises will not pose any 
problems in terms of performance or quality.

There is some flexibility around the panel to prevent damage to the 

 

panel.
The panel might move slightly when it is pushed with a finger, and 

 

clattered sound might be heard. This is not a malfunction.

This is a characteristic of liquid crystal panels and is not a problem. 

 

The liquid crystal panel is built with very high precision technology 
giving you fine picture details. Occasionally, a few non-active pixels 
may appear on the screen as a fixed point of red, green, blue or 
black. Please note this does not affect the performance of your LCD.

Follow the message’s instructions.

 

If the problem persists, contact your local Panasonic dealer or the 

 

authorized Service Centre.