Panasonic KXFLM673HX 작동 가이드
Important Information
3
Important Information
Important Information
For your safety
Laser radiation
Fuser unit
Note:
L
During or immediately after printing, the area near
the recording paper exit (
the recording paper exit (
2) also gets warm. This is
normal.
For best performance
Toner cartridge and drum unit
L
When replacing the toner cartridge or drum unit, do
not allow dust, water, or liquids to come in contact
with the drum. This may affect print quality.
not allow dust, water, or liquids to come in contact
with the drum. This may affect print quality.
L
For optimal performance, genuine Panasonic toner
cartridges and drum units are recommended. We
cannot be responsible for problems that may be
caused by a non-Panasonic toner cartridge or drum
unit:
–
cartridges and drum units are recommended. We
cannot be responsible for problems that may be
caused by a non-Panasonic toner cartridge or drum
unit:
–
Damage to the unit
–
Poor print quality
–
Improper operation
Toner cartridge
L
Do not leave the toner cartridge out of the protection
bag for a long time. It will decrease the toner life.
bag for a long time. It will decrease the toner life.
Drum unit
L
Read the instructions on page 10 before you begin
installation of the drum unit. After you have read
them, open the drum unit protection bag. The drum
unit contains a photosensitive drum. Exposing it to
light may damage the drum. Once you have opened
the protection bag:
–
installation of the drum unit. After you have read
them, open the drum unit protection bag. The drum
unit contains a photosensitive drum. Exposing it to
light may damage the drum. Once you have opened
the protection bag:
–
Do not expose the drum unit to light for more than
5 minutes.
5 minutes.
–
Do not touch or scratch the green drum surface.
–
Do not place the drum unit near dust or dirt, or in
a high humidity area.
a high humidity area.
–
Do not expose the drum unit to direct sunlight.
L
To extend the life of the drum unit, the unit should
never be turned OFF immediately after printing.
Leave the power turned ON for a minimum of 30
minutes after printing.
never be turned OFF immediately after printing.
Leave the power turned ON for a minimum of 30
minutes after printing.
Location
L
To avoid malfunction, do not position the unit near
appliances such as TVs or speakers which generate
an intense magnetic field.
appliances such as TVs or speakers which generate
an intense magnetic field.
Static electricity
L
To prevent static electricity damage to the interface
connectors or other electrical components inside the
unit, touch a grounded metal surface before touching
the components.
connectors or other electrical components inside the
unit, touch a grounded metal surface before touching
the components.
Environment
L
Keep the unit away from electrical noise generating
devices, such as fluorescent lamps and motors.
devices, such as fluorescent lamps and motors.
L
The unit should be kept free from dust, high
temperature and vibration.
temperature and vibration.
L
The unit should not be exposed to direct sunlight.
L
Do not place heavy objects on top of the unit. When
you leave the unit unused for a long period of time,
unplug this unit from the power outlet.
you leave the unit unused for a long period of time,
unplug this unit from the power outlet.
L
The unit should be kept away from heat sources such
as heaters, kitchen stoves, etc. Damp basements
should also be avoided.
as heaters, kitchen stoves, etc. Damp basements
should also be avoided.
L
In the printing process, heat is used to fuse toner
onto the page. As a result, it is normal for the
machine to produce an odour during and shortly after
printing. Be sure to use this unit in an area with
proper ventilation.
onto the page. As a result, it is normal for the
machine to produce an odour during and shortly after
printing. Be sure to use this unit in an area with
proper ventilation.
L
Do not place any objects within 10 cm of the right, left
and back sides of the unit.
and back sides of the unit.
CLASS 1 LASER PRODUCT
The printer of this unit utilises a laser. Use of
controls or adjustments or performance of
procedures other than those specified may
result in hazardous radiation exposure.
controls or adjustments or performance of
procedures other than those specified may
result in hazardous radiation exposure.
Laser diode properties
Laser output : Max. 5 mW
Wavelength : 760 nm – 810 nm
Emission duration : Continuous
Laser output : Max. 5 mW
Wavelength : 760 nm – 810 nm
Emission duration : Continuous
The fuser unit (
1) gets hot. Do not touch it.
1
2