Panasonic DMR-E75V 지침 매뉴얼

[1]

[2]

3, 4, 2, 1] and 

[3]

3, 4, 2, 1] to 

≥You can also set 

the recording time 
with the numeric 
buttons.

≥Maximum recording 

time is 8 hours.

[4]

3, 4, 2, 1] and press 

≥Recording starts.

For your reference
≥It is not possible to change channel or recording mode while 

Flexible Recording is paused.

∫ To exit the FLEXIBLE REC window without recording

Press [RETURN].

∫ To stop recording partway

Press [

∫, STOP].

∫ To show the time 

Press [STATUS] several times.
≥It is displayed in the unit of 

minute.

Note
≥When performing EXT LINK recording (

l right), the flexible 

recording function does not work.

[RAM] [DVD-R]
This function allows you to immediately start recording the same 
programme that you are viewing on the TV.
The programme position selected on the unit automatically changes 
to that of the TV programme that you are viewing on the TV.
Conditions for the Direct TV Recording function:
≥Your TV must be equipped with the [Q Link] function.
≥The unit must be connected to the TV via a fully-wired 21-pin Scart 

cable.

[1]

(

[2]

¥, DIRECT TV REC].

≥Recording of the TV programme that you are viewing on the TV 

starts.

[3]

∫, STOP] to stop recording.

Note
≥When you stop recording, the unit automatically switches back to 

the previously selected programme position.

[RAM] [DVD-R]
If an external equipment (for example a satellite receiver) with a 
timer function is connected to the AV2 terminal of this unit by a 
21-pin Scart cable (

l 12), it is possible to control the recording of the 

unit with the equipment.

Preparation
≥Change the “Ext Link” in the SETUP menu to match the connected 

equipment. (

≥Timer programming has to be done on the external equipment and 

switched to the timer recording standby mode. Refer to the 
equipment’s operating instructions.

[1]

The unit turns off and switches to the recording standby mode.

≥“EXT L” lights on the unit’s display.

The timer recording standby mode is activated on DVD 
(“EXT L” lights on the DVD unit’s display). However, the unit 
may not be turned off automatically.
≥You can play a DVD-RAM on DVD, play or record any media on 

VHS even if the timer recording standby mode is activated on DVD.

≥Recording begins when a signal is received from the connected 

equipment.

≥As long as a video picture is being transmitted by the external 

equipment, the unit will record it.

[2]

≥If the timer recording is started with keeping the unit turned on, 

the unit is not turned off automatically even after the timer 
recording is completed.

When the following message appears on the television screen, press 
[

2, 1] to select “Yes” (continue recording the current programme) 

or “Cancel” (cancel recording) and press [ENTER].

To cancel the external control
Press [EXT LINK] to stop recording or to cancel linked timer 
recording standby.
≥You can also press and hold [∫, STOP] on the DVD main unit for 

more than 3 seconds to stop recording.

≥In order to prevent accidental operation, press [EXT LINK] to 

cancel the setting after recording is finished.

For your reference
≥The video being recorded automatically appears on the television 

when connected to this unit’s AV1 terminal with the 21-pin Scart 
cable.

≥This function does not work with some equipment. Refer to the 

equipment’s operating instructions.

≥The beginnings of recordings may not be recorded correctly in 

some cases.

≥When “Ext Link” is set to “Ext Link 2”, this function does not work if 

the input signal is NTSC system. (

ARD

REC 83

L R

DVD-RAM

Remaining 
time

75VGN.book  25 ページ  ２００４年７月２１日　水曜日　午前１１時５４分