Panasonic DMR-ES30V 작동 가이드
Reference
68
Operation
Page
Picture
Page
Cannot operate the TV.
≥Change manufacturer code. Some TVs cannot be operated even if you change the code.
≥Press [TV/VIDEO] to change the input mode to “TV”.
≥Press [TV/VIDEO] to change the input mode to “TV”.
Cannot operate the DVD.
≥Press [DVD] when operating DVD.
Cannot operate the VHS.
≥Press [VHS] when operating VHS.
The remote control doesn’t
work.
work.
≥The remote control code is wrong. Change to the correct code.
≥The batteries are depleted. Replace them with new ones.
≥Point the remote control at the remote control sensor on the main unit.
≥Remove obstacles between the remote control and main unit.
≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
≥The batteries are depleted. Replace them with new ones.
≥Point the remote control at the remote control sensor on the main unit.
≥Remove obstacles between the remote control and main unit.
≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
≥If you repeatedly insert discs or turn the unit on and off about 50 times or more, the recording
or editing of DVD-R, DVD-RW (DVD-Video format), +R may be disabled.
–
–
–
–
The unit is on but cannot be
operated.
operated.
≥Some operations are prohibited by the disc.
≥The unit is warm (“U59” appears on the unit’s display). Wait until “U59” disappears.
≥One of the unit’s safety devices may have been activated.
≥The unit is warm (“U59” appears on the unit’s display). Wait until “U59” disappears.
≥One of the unit’s safety devices may have been activated.
Reset the unit as follows:
(1) Press [POWER
(1) Press [POWER
Í/I] on the main unit to switch to standby.
If the unit doesn’t switch to standby, press and hold [POWER
Í/I] on the main unit for
about 10 seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC power supply cord, wait for about 1 minute, then
reconnect it.
Alternatively, disconnect the AC power supply cord, wait for about 1 minute, then
reconnect it.
(2) Press [POWER
Í/I] to turn the unit on.
–
–
–
–
–
Cannot eject a disc.
≥The unit is recording
≥The unit may have a problem. While the unit is off, hold down [∫] and [CH, W] on DVD side of
≥The unit may have a problem. While the unit is off, hold down [∫] and [CH, W] on DVD side of
the main unit simultaneously for about 5 seconds. Remove the disc and consult the dealer.
–
–
–
Startup is slow
≥Make sure that “Quick Start” is set to “On”.
Even if “Quick start” is set to “On”, startup is slow if the clock is not set, there was a power
failure or the AC plug has just been connected.
failure or the AC plug has just been connected.
≥A few dozen seconds after turning on the unit, you can play a disc or start recording to discs
other than DVD-RAM.
≥Startup takes time for a few minutes after 4:00 a.m. due to system maintenance of this unit.
–
–
Takes time to read DVD-RAM
≥It may take time to read a disc if it is being used for the first time in this unit or it has not been
used for a long time.
–
TV reception worsens after
connecting the unit.
connecting the unit.
≥This can occur because the signals are being divided between the unit and other equipment. It
can be solved by using a signal booster, available from audio-visual suppliers.
–
The images from the unit do not
appear on the TV.
appear on the TV.
Picture is distorted.
≥Make sure that the TV is connected to the VIDEO OUT terminal, S-VIDEO OUT terminal or
COMPONENT VIDEO OUT terminals on the unit.
≥Make sure that the TV’s input setting (e.g., VIDEO 1) is correct.
≥The TV isn’t compatible with progressive signals. Press and hold [∫] and [“ DVD, DUBBING]
≥The TV isn’t compatible with progressive signals. Press and hold [∫] and [“ DVD, DUBBING]
on DVD of the main unit at the same time for about 5 seconds. The setting will change to
interlace.
interlace.
–
–
–
VHS
DVD
ES30VP&PC.book 68 ページ ２００５年２月２１日 月曜日 午後２時３２分