Panduit ZDF48-RA Industrial Distribution Frame 사양 가이드

Rack mount Ethernet switches shall be deployed and protected 

with an industrial distribution frame (IDF) enclosure which meets 

UL 508A, UL Type 4/12 and IP66. The IDF shall be thermally and 

spatially validated for use in environments up to 50°C. There shall 

be a wall mount option with secure front and rear switch access. 

The IDF shall accommodate two distribution layer switches and 

up to three access layer switches with UPS for commonly used 

copper and fiber based deployments. Optimized power cables, 

receptacles and grounding shall be pre-installed in the enclosure. A 

standardized, pre-configured equipment and accessory layout shall 

be included.

Reduces time required for planning, designing, procurement, and installation

resulting in 25% faster implementation

Incorporate Panduit developed best practices in connectivity, cable

management, wiring, and grounding to ensure network reliability

Provides easy, repeatable design instructions assuring consistency and  

saving time on the job-site

Panduit Laboratories tested the thermal performance with recommended AC 

unit and verified the ambient limitations to 50°C with the specified

network equipment; additional back end space allows for 3X the cooling 

capacity over typical deployments for increased reliability

Limits access to authorized personnel for a secure network

UL 508A Standard for Industrial Control Panels, cUL Listed per CSA, UL Type 4/12 

and IP66 Rated

48.54"H x 23.62"W x 29.95"D (1233mm x 600mm x 761mm)

Wall mount

26 Rack Units , (5) 1U switches and (1) 2U UPS, 96 incoming copper cables

(expandable to 144), 72 strands fiber or 36 fiber duplex ports (expandable to 72-ports)

Maximum load rating of 350 lbs. (158.8kg)

Color and material:  RAL7035 light-gray polyester powder paint; door and backplane made of 16 gauge 

cold roll steel, center and wall sections made of 14 gauge cold roll steel

Validated to 50°C with recommended AC unit

Included with IDF:  Pre-Installed:

(1) Square hole front and rear rack angles, (1) FRME1U fiber enclosure,

(2) CPPL48WBLY 48-port patch panel, (2) CMPHF1 cable management, (1) 

RGRB19CN grounding bar, (3) equipment ground whips, (1)10” DIN Rail, (2) fiber 

spools, (2) back panels, (2) ESD ports, 30” length of duct, (2) duplex, power

receptacles, cage nuts, labeling for cable routing, strain relief bars, (4) power cables
Included Accessories:

(1) ESD wrist strap, (1) HLS-15R0 hook and loop, (1) RGCBNJ660P22 #6 AWG 

grounding cable, mounting hardware, conduit schedule and ingress template, 

installation guide

The Panduit Pre-Configured IDF is engineered to 

deploy and protect 19” rack mount switches on the 

factory floor in an industrial network. Consistent 

design and equipment placement is offered to  

reduce engineering and deployment time.

The IDF wall mount enclosure protects switches, 

both physically and thermally in harsh industrial

environments. It is designed around the use of  

popular fiber based Cisco* 3750X and copper  

based Cisco* 2960S switch deployments.

*Cisco is a registered trademark of Cisco Technology Inc.

^Quantities given for (2) 2960S switches. A 3rd switch may require more connectivity.

+For RUs 1-14 order 2M patch cord FX2ERLNLNSNM002 and for RUs 15-26 order 1M patch cord FX2ERLNLNSNM001.

ZDF48-RA

UTP28SP8INBU-48

®

CJ688TGBU 

PUR6004BU-UY

®

FAP12WAQDLCZ

®

FX2ERLNLNSNM001 

 FX2ERLNLNSNM002 
Opti-Core

®

FODRX24Y

 LC OptiCam

®

FLCDMCXAQY 

  

CPPL48WBLY

SRB19MDBL

SRB19BLY

SRBS19BL-XY

Short (order qty. 2):  CMVDR2S
StructuredGround

™  

 

CNB4K

CNWS1224-C

 N280416G100

3750X

2960S