Weed Instrument 2M59 Multiplexer 사양 가이드
Safety and Warning Information
Important Notice - Before utilizing the product, the user should
determine the suitability of the product for its intended use. The
user assumes all risk and liability in connection with such use.
WEED INSTRUMENT'S WRITTEN WARRANTY FOR THE
PRODUCT IS MADE IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. The user's exclusive remedy for breach of Weed
Instrument's written warranty shall be the repair or replacement
of such quantity of product which is proven to be defective. In no
case shall Weed Instrument be liable for any special, incidental,
or consequential damages based upon breach of contract,
negligence, strict liability or other legal theory.
determine the suitability of the product for its intended use. The
user assumes all risk and liability in connection with such use.
WEED INSTRUMENT'S WRITTEN WARRANTY FOR THE
PRODUCT IS MADE IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. The user's exclusive remedy for breach of Weed
Instrument's written warranty shall be the repair or replacement
of such quantity of product which is proven to be defective. In no
case shall Weed Instrument be liable for any special, incidental,
or consequential damages based upon breach of contract,
negligence, strict liability or other legal theory.
Publication Number:
RM0900169 Rev. 9/05
Fiber Optics
EOTec 2000 MUX Model
2M59
MUX Base Module
Installation Instructions
Optical Compatibility:
1300nm, Single-mode Fiber
with SC Optical Connections
Power Requirements
12 to 30VDC @ 400mA
via the top-front screw
terminal connections
via the top-front screw
terminal connections
--OR—
9VDC @ 200mA from a
2A06 or 2A16 power
supply via the
interconnection bus
2A06 or 2A16 power
supply via the
interconnection bus
Connections
Pluggable, Cage Clamp
Screw Terminal Blocks,
Accept 12 to 24 AWG
Screw Terminal Blocks,
Accept 12 to 24 AWG
Alarm Output Relay
Located at the lower-
front of the module
Form-C (SPDT) rated
1A @ 30VDC
front of the module
Form-C (SPDT) rated
1A @ 30VDC
Update Rate
57.6KHz, independent
of number of
modules/channels
utilized
of number of
modules/channels
utilized
Optical Connection
SC
Optical Fiber Type
Single-Mode
Optical Dynamic Range 11dB, over 9/125 fiber
Ambient Temp. Effect 0.025% / 50°C change
Ambient Conditions
-40 to 85°C
0
to
95%
Humidity
(Non-condensing)
Mounting
35mm DIN Rail
Weight
<
9oz
Flammability Rating
UL V-0
Specifications
Weed Instrument Co., Inc.
Phone: 800-880-9333
512-434-2850
512-434-2850
Fax: 512-434-2851
Email:
fiberop@weedinstrument.com
Visit: www.weedinstrument.com
Connect the DIN Rail, via the Model 2A09 End
Clamp, to protective earth ground with low
impedance. The modules are grounded to PE
when they are snapped onto the DIN Rail. A
Model 2A09 End Clamp on each side of the
module bundle on the DIN rail prevents
accidental disconnection of the modules’
interconnection bus.
Clamp, to protective earth ground with low
impedance. The modules are grounded to PE
when they are snapped onto the DIN Rail. A
Model 2A09 End Clamp on each side of the
module bundle on the DIN rail prevents
accidental disconnection of the modules’
interconnection bus.
When in operation, do not look directly into the
transmit optical port or use magnification or
focusing equipment to view optical output.
transmit optical port or use magnification or
focusing equipment to view optical output.
IEC 60825-1, Class 1 Laser Product
FDA 21 CFR 1040.10 & 1040.11
CAUTION: Use of controls and/or adjustments
or the performance of procedures other than
those specified herein may result in hazardous
radiation exposure.
or the performance of procedures other than
those specified herein may result in hazardous
radiation exposure.