Hitachi CP-WUX645N 사용자 설명서
17
Projector features / Preparations
Power on/off
BLANK
LASER
ASPECT
PUSH
ENTER
PAGE UP
LASER
INDICATOR
MY SOURCE/
DOC.CAMERA
SEARCH
STANDBY/ON
VIDEO
RGB
PAGE DOWN
ESC
MENU
RESET
POSITION
AUTO
PbyP
MAGNIFY
ON
OFF
MY BUTTON
1
2
VOLUME
+
-
FREEZE
KEYSTONE
MUTE
1.
Make sure that the power cord is rmly and
correctly connected to the projector and the outlet.
correctly connected to the projector and the outlet.
Turning on the power
2.
Remove the lens cover, and set the power switch
to the ON position (marked
to the ON position (marked
“
I
”
).
The POWER indicator will light up in steady orange
(
(
72). Then wait several seconds because the
buttons may not function for these several seconds.
3.
Press the STANDBY/ON button on the projector or
the remote control.
the remote control.
• Turn the power on/off in right order. Please power on the projector prior
to the connected devices. Power off the projector later than the connected devices.
• When the AUTO ON of the OPTION Menu is set to the TURN ON, and the power
was turned off by the power switch last time, turning the power switch on makes the
projection lamp light on without pushing the STANDBY/ON button (
• When the AUTO ON of the OPTION Menu is set to the TURN ON, and the power
was turned off by the power switch last time, turning the power switch on makes the
projection lamp light on without pushing the STANDBY/ON button (
47).
• Use the shutdown switch (
74) only when the projector is not turned off by
normal procedure.
NOTE
Power on/off
The projection lamp will light up and the POWER indicator will begin blinking in green. When the power is
completely on, the indicator will stop blinking and light in steady green.
To display the picture, select an input signal according to the section "Selecting an input signal" (
completely on, the indicator will stop blinking and light in steady green.
To display the picture, select an input signal according to the section "Selecting an input signal" (
18, 19).
►A strong light is emitted when the projector’s power is on. Do
not look into the lens of the projector or look inside of the projector through any
of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.
of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.
WARNING
1.
Press the STANDBY/ON button on the projector or the remote control.
The message "Power off?" will appear on the screen for about 5 seconds.
The message "Power off?" will appear on the screen for about 5 seconds.
Turning off the power
2.
Press the STANDBY/ON button on the projector or the remote control again while
the message appears.
The projector lamp will go off, and the POWER indicator will begin blinking in orange.
Then the POWER indicator will stop blinking and light in steady orange when the
lamp cooling is complete.
the message appears.
The projector lamp will go off, and the POWER indicator will begin blinking in orange.
Then the POWER indicator will stop blinking and light in steady orange when the
lamp cooling is complete.
3.
Make sure that the POWER indicator lights in steady orange, and set the
power switch to the OFF position (marked “O”).
The POWER indicator will go off. Attach the lens cover.
power switch to the OFF position (marked “O”).
The POWER indicator will go off. Attach the lens cover.
Do not turn the projector on for 10 minutes or more after turning it off. Also, do not turn
the projector off shortly after turning it on. Such operations might cause the lamp to
malfunction or shorten the lifetime of some parts including the lamp.
the projector off shortly after turning it on. Such operations might cause the lamp to
malfunction or shorten the lifetime of some parts including the lamp.
STANDBY/ON button
POWER indicator
Power
switch