GuangZhou LIWEI Electronics LTD I4S 사용자 설명서

4

The Bluetooth Stereo Headset is composed of:
1.MF Button (

 

) 

  

 

2.Microphone(

 

)

3.Charging Jack(

 

 

)

 

 

4.Speaker(

 

)

5.Earhook(

 

)

   

 

6.Indicator Light(

 

)

7.Previous Song/Volume (-) Button(

 

)

8.Next Song/Volume (+) Button(

 

)

 

Your headset uses a rechargeable battery. You must charge
the battery fully before using the headset for the first time.
Please make sure to turn off the headset before charging.
1. Plugging the charging cradle in the port.

2. The red indicator light remains solid when charging.
3. The fully charging takes approximately2-3 hours.
4. The indicator light is in solid blue when charging completed.

Turn on:Press the MF button until you hear the beep and 
the blue indicator light flashes.
Turn off: Press the MF button until you hear the beep and 
the blue indicator light flashes twice. 

Press and hold the MF button for 2 seconds until you hear 
a long beep.

When you are listening to the music, you can press the MF 
button to play music or make a pause and the volume 
control buttons is to select previous song and next song 
(Briefly press the Volume + to go to next song and Volume  
to go to the previous song.).

6

7

   phone.
   Take the headset away from the mobile phone for more 
   than 10 meters (33ft).

If you want to connect the paired headset with the mobile 
phone, you can do as below:

   Turning on the headset and setting up the connection in 
   the Bluetooth list of your mobile phone
   Pressing once the MF button of the headset. (You have to 
   do the setting in your mobile phone to allow the automatic 
   connection with the paired headset.)

When you hear the ring tone, press the MF button once
If you prefer answering the call by your phone, you can 
transfer the call from the headset on your phone.

Press and release the MF button once or end call on your 
phone's keypad.

If there is ring tone of incoming call when you are listening 
to music from your phone or PC or other Bluetooth enabled 

devices, press the MF button to answer the call and press 
and hold the MF button for 2 seconds to reject the call.

During the phone call, just press and hold the MF button for 
2 seconds to put a call on hold. If you want to resume to the 
call, you can also press and hold the MF button for 2 
seconds. (This is subject to the mobile phone's feature.)

Press and hold the Volume Control (+) to increase volume 
and release when it reaches your preferred volume. Vice 
versa!

5

1. The distance between the Bluetooth headset and your 
  Bluetooth phone would be better within 1 meter when 
  pairing, the closer the better.
2. Ensuring the headset is off.
3. Pressing still the Multifunctional Button until you see the
  blue light remains solid.
4. Set your Bluetooth phone to discover the headset by 
  following your phone's guide. Typically, the steps involved 
  are going to a "Setup" "Connect" or "Bluetooth" menu on 
  your phone and then select the option to discover Blueto-
  oth devices. 
5. Your phone will find the headset and ask if you want to 
  pair with it. Confirming this by pressing “yes” or “ok”.
6.Enter passkey “0000”, then press “yes” or “ok”.

IMPORTANT：If pairing is successful, the indicator light will 
flash in blue 10 times rapidly before going to flashing every 
3 seconds, If unsuccessful, the light remains on, and you will 
need to reattempt the pairing. While the light will go out if the 
pairing time takes more than 60 seconds, in that case, you 
need to turn off the headset and turn it on for pairing again.

If you want to disconnect the headset from the mobile phone, 
you can do as below:
  Turn off the headset
  Disconnect the headset from the Bluetooth list the mobile 
   

2.将充电器插头插入耳机充电接口(     ),另一端插到交流电
  源插座上(如图）.此时耳机开始充电,充电时,红灯(  )恒亮.
3.耳机充足电,大约需要2-3个小时,充满后蓝灯(  )恒亮或红
  灯熄灭.

蓝牙配对步骤:

1

.

配对时,请 将蓝牙耳机 和 手 机 的距离控制在1米 范 围 内,

  越近越好.
2.确 认 蓝 牙耳机处于开 机 状 态.
3.按 多 功 能键(  ),到 蓝 灯(  )恒亮 或 红 蓝灯(  )同时(交
  替)亮,此时 耳 机 进入蓝牙配 对 状 态.
4.按 照 蓝 牙手机的说明 书,打 开"蓝 牙搜索"或"添 加 新 设备"
  选择耳机名称,确 认后按 手 机 的 提 示输入" 0000"确 认.
注意:蓝 牙 耳机的配对 时 间 是 有 限的"一 般 为60秒" ,如果 蓝
     灯(  )熄灭 变 为红灯(  )闪烁状态说 明 蓝 牙 配 对状
     态已 停止.如 果 您这时仍未配 对 成 功,请 重 复 步 骤1 ~4
     再次 配对.

开机或关机

开启耳机时,请按住多功能键(  ),耳机会蜂鸣且蓝色指示灯
(  )会快速闪烁或长按多功能键(  )进入配对状态。
关闭耳机时,请按住多功能键(  ),耳机会蜂鸣且蓝色指示灯
(  )会快速闪烁两下.

将已配对耳机重新连接至手机

要连接耳机和手机,请打开耳机,使用手机的"蓝牙"功能表建立
连接,或按一下多功能键(  ).

断开耳机与手机的连接 

要断开耳机与手机的连接(例如,将手机连接至其他蓝牙设备),
请采用以下任一方式:
  关闭耳机
  使用手机的"蓝牙"功能表断开耳机与手机的连接.
  将耳机移至距离手机10米(约30英尺)以远的位置. 

用户使用说明书

USER  GUIDE

1

    

   耳机由以下部分组成:

1.多功能键(  )              2.麦克风(  )
3.充电插孔(     )           4.听筒(  )
5.耳挂(  )                  6.指示灯(  )
7.

上一曲/音量-（   ）         

8

.下一曲/音量+（   ）

使用入门

耳机充电

本耳机使用内置式不可拆卸充电电池. 请勿尝试从耳机中取出
电池,以免损坏耳机.
1.充电时,先将耳机关机

使用充电器给本耳机充电前,请先检查充电器是否为耳机配套
充电器.
       警告: 必须使用配套的充电器给耳机充电,使用不配套
       的充电器可能会损坏耳机

    充电器和电池

您可以设置手机,使其在耳机启动时自动与耳机建立连接.在手
机中,要实现这一目的,请在"蓝牙"功能表中更改配对设备设置.

接听来电

(  )

来电时,耳机内发出来电提示音或铃声,按下耳机多功能键

,

即可接听来电,或使用手机接听键,接听来电

挂断通话

(  )

按下耳机多功能键

或使用手机挂断键即可挂断通话. 

暂停或保留通话

通话时

，

长按多功能键(  )2秒可保留现有通话，如需恢复通

话,则长按多功能键(  )2秒。(是否支持本功能,取决于手机)

末位重拨

耳机支持末位重拨功能：长按2秒耳机多功能键(  )即可实现
末位重拨。

音乐播放/暂停/选曲

收听音乐时可以操作多功能键(  )播放或暂停,上一曲、下一
曲进行选曲等。(短按一次"+"为下一曲,短-次"-"为上一曲)

音量调节

：

，

音量键调节音量的大小 长按住"+"3秒为音量增大 长按住
"-"3秒为音量减小(注:当音量达到最大或最小时会有蜂鸣声
提示)

拒绝来电

长按2秒耳机多功能键(  )或直接用手机挂断键即可拒绝来电.

2

3

 

Stereo Headset