dresden elektronik ingenieurtechnik gmbh MEGA22M00 사용자 설명서
User Manual
Version 1.1c
2013-07-01
Version 1.1c
2013-07-01
OEM
radio modules deRFmega
www.dresden-elektronik.de
Page 47 of 52
14. Radio certification
14.1. United States (FCC)
The deRFmega128-22M00, deRFmega128-22M10 and deRFmega128-22M12 comply with
the requirements of FCC part 15. The certification process for deRFmega128-22M10 and
deRFmega128-22M12 is pending.
To fulfill FCC Certification requirements, an OEM manufacturer must comply with the
following regulations:
The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is
not visible when the module is installed inside another device, then the outside of the device
into which the module is installed must also display a label referring to the enclosed module.
This exterior label can use wording such as the following. Any similar wording that expresses
the same meaning may be used.
Sample label for radio module deRFmega128-22M00:
FCC-ID: XVV-MEGA22M00
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
The Original Equipment Manufacturer (OEM) must ensure that the OEM modular transmitter
must be labeled with its own FCC ID number. This includes a clearly visible label on the
outside of the final product enclosure that displays the contents shown below. If the FCC ID
is not visible when the equipment is installed inside another device, then the outside of the
device into which the equipment is installed must also display a label referring to the
enclosed equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation
(FCC 15.19). The internal / external antenna(s) used for this mobile transmitter must provide
a separation distance of at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
Installers must be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance. This device is approved as a mobile
device with respect to RF exposure compliance, and may only be marketed to OEM
installers. Use in portable exposure conditions (FCC 2.1093) requires separate equipment
authorization.
the requirements of FCC part 15. The certification process for deRFmega128-22M10 and
deRFmega128-22M12 is pending.
To fulfill FCC Certification requirements, an OEM manufacturer must comply with the
following regulations:
The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is
not visible when the module is installed inside another device, then the outside of the device
into which the module is installed must also display a label referring to the enclosed module.
This exterior label can use wording such as the following. Any similar wording that expresses
the same meaning may be used.
Sample label for radio module deRFmega128-22M00:
FCC-ID: XVV-MEGA22M00
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
The Original Equipment Manufacturer (OEM) must ensure that the OEM modular transmitter
must be labeled with its own FCC ID number. This includes a clearly visible label on the
outside of the final product enclosure that displays the contents shown below. If the FCC ID
is not visible when the equipment is installed inside another device, then the outside of the
device into which the equipment is installed must also display a label referring to the
enclosed equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation
(FCC 15.19). The internal / external antenna(s) used for this mobile transmitter must provide
a separation distance of at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
Installers must be provided with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance. This device is approved as a mobile
device with respect to RF exposure compliance, and may only be marketed to OEM
installers. Use in portable exposure conditions (FCC 2.1093) requires separate equipment
authorization.
Modifications not expressly approved by this company could void the user's authority to
operate this equipment (FCC section 15.21).
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause