PAX Technology Limited PX5RF 사용자 설명서

PAX TECHNOLOGY INC.

P terminals that include a default communication module come

standard with one Ethernet port and RS232, USB, and PUSB

network capabilities. However, if the default communication

module is replaced with an optional communication module,

your choice of these additional network capabilities are

available:

Communication Module

Power Connections

Product Description

• A second Ethernet port

• Power over Ethernet

• An Ethernet hub

• Wi-Fi and Bluetooth LE

• Wi-Fi and Cellular GSM

The commu nication module is located on the underside of

the terminal.

Communication

module

Power down and remove all power from the terminal before

removing or installing a communication module. A

communication module must be installed before power can be

applied to the terminal.

WARNING:

Working Environment: Temperature -10°C～50°C (14°F～122°F)

R.H.: 10%～93% (non-condensing)

Storage Environment: Temperature -20°C～60°C (-4°F～140°F)

R.H.: 5%～95% (non-condensing)

Stylus pen

Touch screen

and

Contactless

reader area

Magnetic

stripe reader

Privacy shield

Keypad

Smart card

reader

Cable retention

cover plate

Communication

ports - located

under cover plate

Speakers

MAC address label

Regulatory label

Communication

module

Communication ports are labeled and color-coded:

White Red Yellow Black

Green

Blue

Part number/

serial number label

Power can be supplied via the power port or a single data cable

that carries power. This power can be provided via a “powered

cable” where the connected POS terminal provides the power

(i.e. PUSB or Power over Ethernet) or by connecting a P power

supply directly to the data cable (i.e. RS232 or USB).

1) Power Port

Insert the power connector into the green POWER port. Turn

the power connector, locking the tab behind the short plastic

wall. Dress the cable through the retention clips. A separate

data cable is also required.

2) POS Cable

Insert the cable connector into the appropriate port on the

terminal. Dress the cable through the retention clips opposite

the port. Connect power supply to cable as required. The cash

3) Power over Ethernet (PoE)

Power is available over the red LAN1 port when the optional

PoE communication module is installed.

Cable Retention Cover Plate

After power and data cables are

connected and dressed through

retention clips, install the cable

retention cover plate and secure

with captive screw.

Screw

Stylus Holder and Pen

Mounting

Locations

Stylus Port

)

Retention

Clips

1) Align stylus holder over
metal screw openings at left
side or top of terminal. Insert
tabs into indentations along
edge. Attach with captive
screws.
2) Insert connector end of
stylus pen into stylus port on
left side of terminal.
3) Use enclosed plastic card to
press stylus cord into retention
clips on left side of terminal.

Privacy Shield

Insert tabs and snap shield firmly in place
to left and right of keypad. Not designed to
be removable. Removing the shield breaks
the retention tabs and the ability to remotely
track the status of the shield is lost.

Privacy Shield

Decorative Plug

Decorative Plug

– If a privacy shield is not

installed, a non-removable decorative plug
may be installed in its place. This plug does
not provide any PIN entry privacy.
CAUTION:

If the privacy shield is not installed,

you must use PCI-approved alternative methods
to secure the PIN pad.

Plugs

1) Stylus Holder Plug
If required, to prevent stylus pen from
being inserted vertically into stylus
holder, firmly insert plug into opening
in holder, aligning with curve of stylus
holder.
2) Smart Card Reader Plug
If required, insert smart card reader
plug into smart card receptacle slot.
To remove, if required, gently pry out
the plug using a small screwdriver in
the slit along top of plug.
3) Ethernet Plug
An Ethernet plug is included in case
you want to block an inactive LAN port.
Align plug so that it matches the shape
of the port and gently push into opening.
To remove, if required, gently pry off
using a small screwdriver in the slit
along the top of the plug.

Note: LAN2 port is enabled only when
Ethernet hub or PoE and Ethernet hub
communication module is installed.

1) Stylus

Holder

Plug

2) Smart Card Reader Plug

3) Ethernet

Plug

Mounting

Slots

Stand Installation

PAX TECHNOLOGY INC.

Route

Cables

If required, the P terminal may be
mounted to a stand.
Instructions may vary depending
on stand specifications.

Carefully route the required cables
up through the stand pipe and out
the top. Connect the cables to the

P terminal ports.

Insert the three mounting slots on
the underside of the terminal into
the three metal prongs on the stand
base.

Slide the terminal firmly into position,
locking the terminal in place on the
stand. Secure with fastening screw
or locking device as required.

Reset Button and Audio Jack

Reset

Button

Audio Jack

If required, restart the
terminal by pressing in
and holding the reset
button for 2-3 seconds

If required, a visually disabled person can connect a
headphone to the terminal for audio prompting using the
3.5mm output audio jack.

Cable Lock

If required, insert customer-provided
cable lock into K-Slot®. Loop cable
around permanent object to secure
in place.

Stylus Port